Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
AQA GCSE Design and Technology Smart practice A mixed round aimed at your weak spots
Unit 1
Core technical principles
Unit 2
Specialist technical principles
Unit 3
Designing and making principles
Investigation, primary and secondary data
Investigation, primary and secondary data
Environmental, social and economic challenge
Environmental, social and economic challenge
Design strategies
Design strategies
Communication of design ideas
Communication of design ideas
Prototype development
Prototype development
Selection of materials and components
Selecting materials and components for prototypes
Specialist tools and equipment
Specialist tools and equipment
Avg
score:
–
Topics
done:
0/40

Working accurately to tolerances

Practise 18 exam-style questions on Working accurately to tolerances for AQA GCSE Design and Technology. Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 18 questions
  • 1–8 marks each
  • Instant marking
  • No sign-up needed
18 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

A double-ended plug gauge is used to check that drilled holes are within tolerance.

Which result shows that a hole is within tolerance?

Choose your answer.

  • neither end enters the hole
  • both ends enter the hole
  • the NO GO end enters but the GO end does not
  • the GO end enters but the NO GO end does not

Model answer

the GO end enters but the NO GO end does not

Explanation

The GO end of a plug gauge is made to the minimum acceptable hole size and the NO GO end to the maximum. A good hole is at least the minimum size, so the GO end fits, but no bigger than the maximum, so the NO GO end does not. Gauges give a quick pass or fail without reading a measurement, which suits checking large batches.

Mark scheme
  1. 1 mark

    the GO end enters but the NO GO end does not

    If more than one option is given, 0 marks. If neither end enters, the hole is smaller than the minimum size (undersize). If both ends enter, the hole is larger than the maximum size (oversize). 'The NO GO end enters but the GO end does not' cannot happen with a correct gauge, because the GO end is the smaller of the two.

Question 2

3 marks

The four legs of a table must each be 720 mm ± 2 mm long. A worker measures the legs cut for one table:
- Leg A: 719.5 mm
- Leg B: 722.5 mm
- Leg C: 717.0 mm
- Leg D: 721.0 mm

Work out the maximum and minimum acceptable lengths, and state which legs can be used.

Model answer

Maximum = 720 + 2 = 722 mm
Minimum = 720 - 2 = 718 mm
Leg A (719.5 mm) and leg D (721.0 mm) are between 718 mm and 722 mm, so they can be used. Leg B is 0.5 mm too long and leg C is 1.0 mm too short.

Explanation

Add the tolerance to the nominal size for the maximum and subtract it for the minimum, then compare each measurement with both limits. Leg B could be trimmed to size, but leg C is too short and has to be remade, which wastes material. Even legs within tolerance can differ by up to 4 mm, so a maker may still trim them to match.

Mark scheme
  1. 1 mark

    maximum = 720 + 2 = 722 mm

    Award full marks for a correct answer, even with no working shown. Mark the numbers, not the units.

  2. 1 mark

    minimum = 720 - 2 = 718 mm

  3. 1 mark

    legs A and D (only)

    Both A and D are needed, with B and C not included. ft their maximum and minimum if the legs chosen are correct for their limits.

Question 3

3 marks

A printer trims business cards to 85 mm × 55 mm ± 0.5 mm. A sample of 40 cards from a batch of 1200 is measured, and 3 of the cards are outside the tolerance.

Calculate the percentage of the sample that is outside the tolerance, and estimate how many cards in the whole batch are likely to be outside the tolerance.

Model answer

Percentage outside tolerance = 3 ÷ 40 × 100 = 7.5%
Estimated cards outside tolerance in the batch = 7.5% of 1200 = 0.075 × 1200 = 90 cards

Explanation

Measuring a sample is quicker than measuring every product, and the sample's reject rate is used to estimate the whole batch. A reject rate of 7.5% is high, so the printer would check the guillotine settings and crop marks before trimming more cards. The estimate assumes the sample is typical of the batch.

Mark scheme
  1. 1 mark

    Step 1: 3 ÷ 40 = 0.075

    Award full marks for correct answers, even with no working shown.

  2. 1 mark

    Step 2: 0.075 × 100 = 7.5%

  3. 1 mark

    Step 3: 7.5% of 1200 = 0.075 × 1200 = 90 cards

    ft their percentage. Accept 'about 90'. 1200 ÷ 40 × 3 = 90 is an equally valid method.

Question 4

4 marks

An electronics company is designing the timer circuit for a toaster. The toasting time depends on the value of a resistor in the circuit.

Analyse and evaluate using ±1% metal film resistors, rather than ±5% carbon film resistors, in this circuit in terms of the performance of the toaster.

Model answer

The toasting time depends on the resistor's value, so its tolerance directly affects how long the toaster toasts. With ±5% resistors, a toaster set to 120 seconds could toast anywhere from about 114 to 126 seconds, so two toasters on the same setting could brown bread differently. With ±1% resistors the variation is only about 119 to 121 seconds, so every toaster performs the same and customers get the result they expect. Metal film resistors are also more stable as they warm up, so the time does not drift as the toaster gets hot.
However, metal film resistors cost a little more, which adds up over thousands of toasters. The timing also depends on the capacitor in the circuit, which may have a tolerance of ±10% or more, so using 1% resistors alone may not improve consistency much unless the capacitor is also chosen carefully.
Overall, I think ±1% resistors are worth using, because the extra cost per toaster is very small and they make the timing more consistent and stable, as long as the capacitor tolerance is also controlled.

Explanation

Level 2 needs the effect of tolerance on toasting time explained, positive and negative factors weighed, and a conclusion. The best answers use numbers to show the effect and recognise that other components' tolerances matter too. Answers that only say '1% is more accurate' stay in Level 1.

Mark scheme
  1. 4 marks

    Levels of response (4 marks).
    Level 2 (3-4 marks): Well described and justified analysis of the effect of resistor tolerance on the performance of the toaster, containing full evaluation, drawing on conclusions having considered both positive and negative factors.
    Level 1 (1-2 marks): Brief points mentioned but not fully explained. Analysis present but limited evaluation/conclusions drawn. May have focused solely on either positive or negative factors.
    0 marks: No attempt or nothing worthy of credit.

    Indicative content (illustrative, not exhaustive; credit any worthy points made in support of the band descriptors). Positive: a ±1% resistor is within 1% of its stated value, so the toasting time varies by only about 1% from one toaster to the next, instead of up to 5% (e.g. a 120 s setting could be 114-126 s with ±5%, but about 119-121 s with ±1%); every toaster browns bread consistently at the same setting, so customers get the result they expect and there are fewer complaints or returns; metal film resistors are also more stable as they warm up and age, so the timing does not drift when the toaster gets hot; tighter tolerances may remove the need to adjust each circuit during manufacture. Negative: metal film resistors cost slightly more, which adds up over thousands of toasters (though resistors are cheap, so the increase per product is small); the timing also depends on other components, e.g. a capacitor with a tolerance of ±10% or ±20%, so a 1% resistor alone may not make much difference unless the capacitor is also chosen carefully or the circuit is calibrated; the user's browning control already lets the time be adjusted. Evaluation: a judgement, e.g. ±1% resistors are worthwhile because they improve consistency for very little extra cost, provided the other timing components are also chosen to suit. Analysis: identification of how resistor tolerance affects the toasting time and the toaster's performance. Evaluation: judgement weighing the benefit against the cost and the other components. Accept all other valid responses.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.