Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
AQA GCSE Design and Technology Smart practice A mixed round aimed at your weak spots
Unit 1
Core technical principles
Unit 2
Specialist technical principles
Unit 3
Designing and making principles
Investigation, primary and secondary data
Investigation, primary and secondary data
Environmental, social and economic challenge
Environmental, social and economic challenge
Design strategies
Design strategies
Communication of design ideas
Communication of design ideas
Prototype development
Prototype development
Selection of materials and components
Selecting materials and components for prototypes
Specialist tools and equipment
Specialist tools and equipment
Avg
score:
–
Topics
done:
0/40

Sources and origins of materials

Practise 20 exam-style questions on Sources and origins of materials for AQA GCSE Design and Technology. Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 20 questions
  • 1–8 marks each
  • Instant marking
  • No sign-up needed
20 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

2 marks

Aluminium is extracted from an ore.

Name the ore, and name the process used to extract aluminium from it.

Model answer

The ore is bauxite. Aluminium is extracted from it by electrolysis.

Explanation

Bauxite is first refined into pure aluminium oxide (alumina). Because aluminium is more reactive than carbon, it cannot be extracted in a blast furnace like iron; instead the alumina is dissolved in molten cryolite and split by electrolysis, which uses a very large amount of electricity.

Mark scheme
  1. 1 mark

    Ore: bauxite

    Do not accept 'aluminium oxide' or 'alumina' for the ore: alumina is made from bauxite.

  2. 1 mark

    Process: electrolysis

    Accept 'electrolytic reduction' or 'the Hall-Heroult process'. Accept 'the Bayer process followed by electrolysis'. Do not accept 'the Bayer process' alone (it refines bauxite to alumina but does not produce aluminium), 'smelting' alone, 'blast furnace' or 'heating with carbon'.

Question 2

3 marks

Explain how cracking makes the fractions obtained from crude oil more useful for making polymers.

Model answer

Cracking breaks long-chain hydrocarbon molecules, such as those in the naphtha fraction, into shorter molecules, using heat and a catalyst or very high temperatures with steam. This produces small, reactive molecules such as ethene and propene, which are the monomers that are polymerised to make polyethylene and polypropylene. Crude oil naturally contains more long-chain molecules than are needed, so cracking turns these into the small molecules that polymer makers want.

Explanation

Fractional distillation only separates the hydrocarbons already in crude oil; it does not change them. Cracking changes them, breaking big molecules into small ones, and is the step that creates most of the monomers for polymers. A common mistake is to describe distillation when asked about cracking.

Mark scheme
  1. 1 mark

    Cracking breaks down long-chain hydrocarbon molecules (e.g. from the naphtha fraction) into shorter-chain molecules

    One mark for each correct point, max 3. Do not credit descriptions of fractional distillation (separating by boiling point) as cracking.

  2. 1 mark

    using heat and a catalyst (catalytic cracking), or very high temperatures with steam (steam cracking)

  3. 1 mark

    It produces small, reactive molecules (alkenes) such as ethene and propene, which are the monomers used to make polymers such as polyethylene (polythene) and polypropylene

    Accept 'it makes monomers that can be polymerised'.

  4. 1 mark

    Fractional distillation produces more long-chain fractions than are needed and too few small molecules, so cracking turns surplus fractions into useful ones

    Accept all other valid responses.

Question 3

3 marks

A reel of electrical cable is 500 m long. Each metre of the cable contains 18 g of copper.

The copper ore that the copper was extracted from contained 0.6% copper by mass.

Calculate the mass of ore that had to be mined to obtain the copper for the reel. Give your answer in tonnes. (1 tonne = 1000 kg)

Model answer

Copper in the reel = 500 × 18 g = 9000 g = 9.0 kg
Ore needed = 9.0 ÷ 0.006 = 1500 kg
= 1.5 tonnes

Explanation

A percentage of 0.6% means 0.006 as a decimal, so the mass of ore is the mass of copper divided by 0.006. The answer shows why mining has such a large impact: 1.5 tonnes of rock are dug up to produce just 9 kg of copper, which must then be smelted and refined by electrolysis to make it pure enough for electrical cable.

Mark scheme
  1. 1 mark

    Step 1: copper in the reel = 500 × 18 = 9000 g = 9.0 kg

    Award full marks for a correct answer, even with no working shown. The unit is given, so mark the number: accept 1.5.

  2. 1 mark

    Step 2: mass of ore = 9.0 ÷ 0.006 (or 9.0 ÷ 0.6 × 100) = 1500 kg

    ft their Step 1 value. An answer of 15 (dividing by 0.6 instead of 0.006) scores Step 1 only.

  3. 1 mark

    Step 3: 1500 kg = 1.5 tonnes

    ft their Step 2 value converted correctly to tonnes. An answer of 1500 with no conversion scores Steps 1 and 2.

Question 4

6 marks

Choose one of these materials:
- paper, from wood
- seasoned timber planks, from a standing tree
- steel, from iron ore
- polymer granules, from crude oil
- cotton yarn, from the cotton plant
- copper wire for electrical circuits, from copper ore

Describe, in a logical sequence, the main stages in converting your chosen material from its primary source into a workable form.

Model answer

I have chosen polymer granules from crude oil.

First, crude oil is extracted by drilling, then transported by pipeline or tanker to a refinery. There it is heated in a furnace until most of it turns to vapour and is fed into the bottom of a tall fractionating column. The column is hottest at the bottom and coolest at the top, so the hydrocarbons condense at different heights according to their boiling points and are drawn off as fractions. This is fractional distillation.

The naphtha fraction, which contains long-chain molecules, is then cracked. In steam cracking it is heated to a very high temperature with steam, which breaks the long chains into small molecules called monomers, such as ethene and propene.

Next, the monomers are polymerised in a reactor, using heat, pressure and a catalyst, so that thousands of monomers join together into long polymer chains, for example ethene into polyethylene.

Finally, additives such as UV stabilisers and pigments are mixed in, and the polymer is melted, extruded into thin strands and chopped into small granules. The granules are bagged and sold to manufacturers for injection moulding, extrusion or blow moulding.

Explanation

Top-level answers give the stages in the correct order, use the correct technical terms (fractional distillation, cracking, polymerisation; or pulping, calendering; or ginning, carding, spinning; or smelting, electrolysis, wire drawing) and name specific equipment such as a fractionating column, blast furnace, kiln, wire mesh, spinning frame or drawing dies. Missing out a key stage, or putting stages in the wrong order, keeps an answer in Level 2.

Mark scheme
  1. 6 marks

    Levels of response (6 marks).
    Level 3 (5-6 marks): A detailed description making several correct points for the selected process. Specific correct and appropriate process stages in a logical sequence, with specific equipment given.
    Level 2 (3-4 marks): A description with points showing some understanding of the selected process. Basic reference made to some stages of the process, with some equipment given.
    Level 1 (1-2 marks): Simple notes showing limited understanding of the selected process.
    0 marks: No response or nothing worthy of credit.

    Indicative content (illustrative, not exhaustive; credit any worthy points made in support of the band descriptors): Paper: trees felled and logs debarked and chipped; chips pulped mechanically (ground) or chemically (cooked to dissolve the lignin), or recycled paper pulped and de-inked; pulp washed, screened and bleached; sizing, fillers (e.g. china clay) and dyes added; very dilute pulp (over 99% water) flowed from the headbox onto a moving wire mesh, where water drains away; web pressed between felt-covered rollers, dried over heated cylinders, calendered (smoothed between rollers) and wound onto reels or cut into sheets. Timber planks: tree felled, branches removed, logs transported to a sawmill; debarked; converted by through-and-through or quarter sawing on a bandsaw; boards stacked with stickers (spacers) and ends sealed; seasoned by air (covered, open-sided shed, months or years, about 15-20% moisture content) or in a kiln (controlled heat, humidity and fans, days or weeks, about 8-12%); moisture content checked with a meter; planed and cut to standard sizes. Steel: iron ore mined, crushed and sintered; ore, coke and limestone fed into the top of a blast furnace; hot air blasted in at the bottom; coke burns and forms carbon monoxide, which reduces the iron oxide; limestone removes impurities as slag; molten iron (about 4% carbon) tapped off; refined in a basic oxygen furnace (oxygen blown through, often with scrap steel) to reduce the carbon; alloying elements added; cast and rolled into sheet, bar, rod or tube. Polymer granules: crude oil drilled and piped or shipped to a refinery; heated and separated into fractions by fractional distillation in a fractionating column; naphtha cracked (steam or catalytic) into monomers such as ethene and propene; monomers polymerised in a reactor; additives (stabilisers, pigments) mixed in; polymer extruded and chopped into granules. Cotton yarn: cotton bolls picked; ginned to separate the fibres from the seeds; pressed into bales; opened and cleaned; carded to untangle and align the fibres into a sliver; combed for fine yarn; drawn out and spun (twisted) into yarn on a spinning frame; wound onto cones. Copper wire: copper ore (e.g. chalcopyrite, often below 1% copper) mined, usually in open-pit mines; crushed and ground to a powder; concentrated by froth flotation; smelted in a furnace and air blown through to give impure (blister) copper, which is fire refined and cast into anodes; refined by electrolysis (impure copper anode, pure copper cathode, copper sulfate solution) to about 99.99% pure copper, needed for good electrical conductivity; low-grade ores may instead be leached and the copper recovered by electrolysis; cathodes melted and cast into rod; rod drawn through a series of dies into wire, annealed (heated to soften it) and coated with PVC insulation. Accept all other valid responses.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.