Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
AQA GCSE Design and Technology Smart practice A mixed round aimed at your weak spots
Unit 1
Core technical principles
Unit 2
Specialist technical principles
Unit 3
Designing and making principles
Investigation, primary and secondary data
Investigation, primary and secondary data
Environmental, social and economic challenge
Environmental, social and economic challenge
Design strategies
Design strategies
Communication of design ideas
Communication of design ideas
Prototype development
Prototype development
Selection of materials and components
Selecting materials and components for prototypes
Specialist tools and equipment
Specialist tools and equipment
Avg
score:
–
Topics
done:
0/40

Physical and working properties of materials

Practise 20 exam-style questions on Physical and working properties of materials for AQA GCSE Design and Technology. Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 20 questions
  • 1–8 marks each
  • Instant marking
  • No sign-up needed
20 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

Which one of the following is a unit of density?

Choose your answer.

  • g/m²
  • N/mm²
  • kg
  • g/cm³

Model answer

g/cm³

Explanation

Density is mass per unit volume (density = mass ÷ volume), so its units are a mass unit divided by a volume unit, such as g/cm³ or kg/m³. Water has a density of 1 g/cm³ (1000 kg/m³). A common confusion is with paper weight in g/m² (gsm), which is mass per unit area.

Mark scheme
  1. 1 mark

    g/cm³

    If more than one option is given, 0 marks. 'g/m²' is wrong: it is mass per unit area, used for the weight (grammage) of paper and fabric (gsm), not mass per unit volume. 'N/mm²' is wrong: it is force per unit area, a unit of stress or pressure. 'kg' is wrong: it is a unit of mass only.

Question 2

2 marks

Workers who repair overhead electricity cables use ladders made from glass reinforced plastic (GRP) rather than aluminium ladders.

Explain why.

Model answer

Aluminium is a metal and a good electrical conductor, but GRP is an electrical insulator. If an aluminium ladder touched a live cable, current could flow through the ladder and the worker, giving them a possibly fatal electric shock, while a GRP ladder would not conduct.

Explanation

Electrical conductivity is a physical property: metals conduct electricity, while most polymers and composites such as GRP do not. That is why ladders for electrical work, plug cases and cable insulation are made from non-metals. A good answer states the property and then explains the danger it removes.

Mark scheme
  1. 1 mark

    Aluminium (a metal) is a good electrical conductor, while GRP is an electrical insulator (non-conductor)

    Accept either half: 'aluminium conducts electricity' or 'GRP does not conduct electricity'.

  2. 1 mark

    So if the ladder touched a live cable, current could flow through an aluminium ladder and the worker, giving an electric shock; a GRP ladder greatly reduces this risk

    Do not accept 'GRP is stronger' or 'GRP is lighter' (aluminium ladders are usually lighter). Do not accept answers about heat or thermal conductivity. Accept all other valid responses.

Question 3

3 marks

A student compared the hardness of four materials. A hardened steel ball was pressed into each sample with the same force, and the diameter of the dent it left was measured. The test was done three times on each material. The table shows the results.

Calculate the mean dent diameter X for sample C. State which sample is the hardest and give a reason for your answer.

Table with columns "Sample", "Material", "Dent 1 in mm", "Dent 2 in mm", "Dent 3 in mm", "Mean in mm". Sample: A; Material: Pine; Dent 1 in mm: 6.2; Dent 2 in mm: 5.8; Dent 3 in mm: 6.0; Mean in mm: 6.0 | Sample: B; Material: Aluminium; Dent 1 in mm: 3.1; Dent 2 in mm: 3.3; Dent 3 in mm: 3.2; Mean in mm: 3.2 | Sample: C; Material: Low carbon steel; Dent 1 in mm: 1.7; Dent 2 in mm: 1.5; Dent 3 in mm: 1.6; Mean in mm: X | Sample: D; Material: Acrylic; Dent 1 in mm: 4.4; Dent 2 in mm: 4.6; Dent 3 in mm: 4.5; Mean in mm: 4.5.

Model answer

Mean for C = (1.7 + 1.5 + 1.6) ÷ 3 = 4.8 ÷ 3 = 1.6 mm
Sample C, low carbon steel, is the hardest because it has the smallest mean dent, so the ball pressed into it the least.

Explanation

Hardness is resistance to indentation and scratching, so with the same force a harder material is dented less. The mean is the total of the three results divided by three. Repeating the test and using a mean makes the comparison more reliable; a common mistake is to think the biggest number shows the hardest material.

Mark scheme
  1. 1 mark

    Step 1: (1.7 + 1.5 + 1.6) ÷ 3 OR 4.8 ÷ 3

    Award full marks for a correct mean and correct choice with a reason, even with no working shown.

  2. 1 mark

    Step 2: X = 1.6 (mm)

    Accept 1.6 mm or 1.60.

  3. 1 mark

    Sample C (low carbon steel) is the hardest, because it has the smallest (mean) dent diameter / the ball sank in least

    The reason is needed for this mark. ft their mean for C: if their mean is not the smallest, credit the sample with the smallest mean. Do not accept sample A because it has the 'biggest number' (the biggest dent shows the softest material).

Question 4

6 marks

Students in a design and technology workshop often cut card with a craft knife against the edge of a ruler. A teacher is choosing between two 300 mm rulers.

Ruler A: stainless steel, 1 mm thick, with the markings etched into the surface.
Ruler B: acrylic, 3 mm thick, transparent, with the markings printed on the back.

Analyse and evaluate the suitability of each ruler for the workshop, in terms of the physical and working properties of the materials.

Model answer

Ruler A is stainless steel, which is a hard material. When a student runs a craft knife along its edge the blade cannot cut into the steel, so the edge stays perfectly straight and every cut is accurate. Steel is also tough, so the ruler will not snap if it is dropped on the floor, and it is elastic, so if it is bent it springs back straight. Stainless steel does not rust, and because the markings are etched into the surface they will not rub off. It is denser than acrylic, so it is heavier and less likely to slip while cutting. Its main drawbacks are that it is opaque, so students cannot see the work underneath, and it costs more.

Ruler B is acrylic. It is transparent, so students can see their lines through it and position it accurately, and it is light. The printed markings on the back are protected from wear. However, acrylic is much softer than steel, so a craft knife will soon nick and shave the edge. The edge then becomes uneven, the cuts are no longer straight and the blade could slip towards the student's fingers. Acrylic is also brittle, so the ruler could crack or snap if it is dropped, leaving sharp edges, and its surface scratches easily, making it harder to see through.

Overall, Ruler A is far more suitable for cutting in the workshop because its hardness and toughness make it accurate, long-lasting and safer. Ruler B is still useful for drawing and measuring, where being able to see through it is an advantage, but it should not be used as a cutting edge.

Explanation

The top level needs both rulers analysed using named properties (hardness, toughness, elasticity, density, transparency) linked to what happens in the workshop, plus a judgement about which suits which job. Simply saying 'steel is strong' or 'acrylic is see-through' without explaining the effect stays in Level 1. The key point is hardness: a craft knife damages a soft acrylic edge but not a steel one.

Mark scheme
  1. 6 marks

    Levels of response (6 marks).
    Level 3 (5-6 marks): Thorough analysis and evaluation of both rulers considering the physical and working properties of stainless steel and acrylic for use in the workshop.
    Level 2 (3-4 marks): Good analysis and simple evaluative points of one or more rulers considering the physical and working properties of the materials.
    Level 1 (1-2 marks): Basic analysis of one or two simple property points for either ruler.
    0 marks: No response or nothing worthy of credit.

    Indicative content (illustrative, not exhaustive; credit any worthy points made in support of the band descriptors): Ruler A (stainless steel): hard, so a craft knife blade slides along the edge without cutting into it and the edge stays straight, giving accurate, safe cuts; tough, so it will not snap if dropped or bent; elastic, so it can flex and spring back (e.g. to measure a curve) without permanent bending; corrosion resistant, so it does not rust if it gets damp; etched markings will not wear off; denser and heavier than acrylic, so it stays put when held down for cutting; but it is opaque, so the work underneath cannot be seen; it conducts heat and electricity (not a problem for measuring and cutting, but it should not be used near live circuits); higher cost; thin edges and corners can be sharp. Ruler B (acrylic): transparent, so students can see lines and work underneath and line it up accurately; low density, so light; markings on the back are protected from wear; cheaper; but acrylic is much softer than steel, so the knife can nick or shave the edge, making it uneven and inaccurate and letting the blade slip towards fingers; it is brittle (low toughness), so it can crack or snap if dropped or bent, leaving sharp pieces; its surface scratches easily, making it harder to see through. Analysis: identification of how the hardness, toughness, elasticity, density and transparency of each material affect accuracy, safety and lifespan in the workshop. Evaluation: judgements, e.g. the steel ruler is the better choice for cutting because it is hard, tough and safe; the acrylic ruler is better kept for drawing and measuring, where seeing through it helps. Accept all other valid responses.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.