Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
AQA GCSE Design and Technology Smart practice A mixed round aimed at your weak spots
Unit 1
Core technical principles
Unit 2
Specialist technical principles
Unit 3
Designing and making principles
Investigation, primary and secondary data
Investigation, primary and secondary data
Environmental, social and economic challenge
Environmental, social and economic challenge
Design strategies
Design strategies
Communication of design ideas
Communication of design ideas
Prototype development
Prototype development
Selection of materials and components
Selecting materials and components for prototypes
Specialist tools and equipment
Specialist tools and equipment
Avg
score:
–
Topics
done:
0/40

Systems approach to designing

Practise 22 exam-style questions on Systems approach to designing for AQA GCSE Design and Technology. Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 22 questions
  • 1–8 marks each
  • Instant marking
  • No sign-up needed
20 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

Which output device should a designer choose for a product that must play recorded speech and music?

Choose your answer.

  • Speaker
  • Buzzer
  • Lamp
  • Microphone

Model answer

Speaker

Explanation

A speaker converts a changing electrical signal into sound, so it can reproduce a wide range of sounds such as speech and music. A buzzer gives only one tone, so it suits warnings. A common mistake is to choose a microphone, which is an input, not an output.

Mark scheme
  1. 1 mark

    Speaker

    If more than one option is given, 0 marks. Buzzer is wrong: a buzzer produces a single loud tone (a beep), not speech or music. Lamp is wrong: a lamp produces light, not sound. Microphone is wrong: a microphone is an input device that converts sound into an electrical signal; it does not produce sound.

Question 2

2 marks

A microcontroller makes the LED in a road-works warning lamp flash. The program repeats these four steps over and over:

LED on
wait 200 ms
LED off
wait 300 ms

Calculate how many times the LED flashes in one minute.

Model answer

One flash = 200 ms + 300 ms = 500 ms = 0.5 s
1 minute = 60 000 ms
60 000 ÷ 500 = 120
Answer: 120 flashes

Explanation

A full cycle of the program is one 'on' time plus one 'off' time, so each flash takes 500 ms. There are 60 000 ms in a minute, so the LED flashes 120 times. Using wait times in the program is how a microcontroller acts as a timer; the common error is to use only the 'on' time.

Mark scheme
  1. 1 mark

    Step 1: one flash takes 200 + 300 = 500 ms (0.5 s)

    Award full marks for a correct answer, even with no working shown.

  2. 1 mark

    Step 2: 60 000 ÷ 500 = 120 (flashes)

    ft 60 000 ÷ their time for one flash in ms (or 60 ÷ their time in s). 60 000 ÷ 200 = 300 scores 0; 60 ÷ 0.2 = 300 scores 0.

Question 3

3 marks

A computer case has a cooling fan that a microcontroller switches on when the inside of the case gets too hot. An NTC thermistor is used as the input sensor.

Explain how the system switches the fan on.

Model answer

As the case gets hotter, the resistance of the NTC thermistor falls, which changes the voltage at the microcontroller's input. The microcontroller's program compares this reading with a set value, such as the voltage for 40 °C, and decides whether the case is too hot. When the set value is passed, it switches its output on, which turns on the fan through a transistor, and when the case cools it switches the fan off again.

Explanation

This is a full input-process-output system: the thermistor senses the temperature, the microcontroller makes a decision by comparing the reading with a set value, and the fan is the output. Remember that an NTC thermistor's resistance falls as the temperature rises. Answers that just say 'the thermistor detects heat and turns the fan on' miss the process stage.

Mark scheme
  1. 1 mark

    As the temperature rises, the resistance of the (NTC) thermistor falls

    Award 1 mark for each creditworthy point; a point explained in detail earns 2 marks. max 3. Do not credit 'the resistance of the thermistor rises as it gets hotter' (this is wrong for an NTC thermistor).

  2. 1 mark

    This changes the voltage at the microcontroller's input (the thermistor is in a voltage divider with a fixed resistor)

  3. 1 mark

    The microcontroller compares the input with a value set in its program (decision making), e.g. 'is the temperature above 40 °C?'

  4. 1 mark

    When the set value is passed, the microcontroller switches its output on, which turns on the fan (through a transistor or driver, because the fan needs more current than the microcontroller can supply)

  5. 1 mark

    When the case cools down, the resistance rises again and the microcontroller switches the fan off

    Accept all other valid responses.

Question 4

6 marks

Explain how programmable microcontrollers can be used as counters, as timers and for decision making to improve the functionality of products.

Give examples in your answer.

Model answer

A microcontroller is a small computer on one chip that forms the process block of a system. It reads signals from input sensors, follows the program stored in it, and switches outputs on and off. Because it is programmed, one chip can be used as a counter, a timer and a decision maker at the same time.

As a counter, the program adds 1 each time an input changes. In a car park, a sensor at the entrance sends a pulse for each car, the microcontroller adds it to the count, and when the count reaches the number of spaces it lights the 'FULL' sign. A cycle computer counts each turn of the wheel and multiplies by the wheel's circumference to show the distance travelled.

As a timer, the program waits for a set time before changing an output. A bathroom extractor fan keeps running for 10 minutes after the light is turned off, so steam is cleared, and an electric toothbrush beeps every 30 seconds to tell the user to move to the next part of their mouth.

For decision making, the program compares an input with a set value and chooses what to do. A room thermostat reads a thermistor and switches the heating on only when the temperature is below the setting, which saves energy. A digital thermometer lights a red LED and beeps if the reading is 38 °C or above.

These functions make products automatic, safer and more efficient. Because the behaviour is set by the program, a designer can change a time, a count or a set value, or add a new feature, without changing the circuit, so products can be customised and updated cheaply.

Explanation

A Level 3 answer explains all three uses, each with a specific product example, and links them to better functionality (automatic, safer, energy-saving, customisable). Without examples the maximum is four marks. A common pitfall is to describe what a microcontroller is without explaining how its program counts, times or makes decisions.

Mark scheme
  1. 6 marks

    Levels of response (6 marks).
    Level 3 (5-6 marks): A thorough and detailed explanation with clear, relevant discussion of how microcontrollers are used as counters, as timers and for decision making. Excellent understanding of how this improves the functionality of products. Clear example(s) given to support the response.
    Level 2 (3-4 marks): A good explanation with relevant supporting discussion of how microcontrollers are used. Some understanding of how this improves the functionality of products. There may be example(s) given to support the response.
    Level 1 (1-2 marks): Basic discussion with general points made around microcontrollers and what they are. Little or no consideration of examples to support the response.
    0 marks: No response or nothing worthy of credit.

    Maximum of four marks for detailed points but no examples given. Indicative content (illustrative, not exhaustive; credit any worthy points made in support of the band descriptors): A microcontroller is a small programmable computer on a single chip; it reads inputs, follows its program and controls outputs (the process block). Counters: the program adds 1 each time an input changes, e.g. counting people through a turnstile or cars into a car park and lighting a 'full' sign; a cycle computer counting wheel turns to work out distance; a step counter; counting items on a production line; a games controller or quiz system keeping score. Timers: the program waits for a set time or measures time, e.g. an extractor fan that runs on for 10 minutes; a toaster or microwave oven cooking time; an electric toothbrush that buzzes every 30 seconds; flashing LEDs on a bicycle light; traffic or pedestrian crossing lights; a night light that switches off after 30 minutes to save energy. Decision making: the program compares an input with a set value and chooses what to do (if ... then ...), e.g. a thermostat switching a heater on below 18 °C; a street light switching on when an LDR shows it is dark; a fever thermometer showing a red LED at 38 °C or above; a kettle switching off when it boils. Combining functions: e.g. a washing machine programme uses timing, counting (drum turns, rinses) and decisions (water level, temperature) at once. Improving functionality: products become automatic, safer, more efficient (save energy), more accurate; the program can be changed to customise or update the product without changing the hardware; one chip replaces many components, so products are smaller and cheaper to make. Accept all other valid responses.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.