Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
AQA GCSE Design and Technology Smart practice A mixed round aimed at your weak spots
Unit 1
Core technical principles
Unit 2
Specialist technical principles
Unit 3
Designing and making principles
Investigation, primary and secondary data
Investigation, primary and secondary data
Environmental, social and economic challenge
Environmental, social and economic challenge
Design strategies
Design strategies
Communication of design ideas
Communication of design ideas
Prototype development
Prototype development
Selection of materials and components
Selecting materials and components for prototypes
Specialist tools and equipment
Specialist tools and equipment
Avg
score:
–
Topics
done:
0/40

Types of movement and levers

Practise 22 exam-style questions on Types of movement and levers for AQA GCSE Design and Technology. Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 22 questions
  • 1–8 marks each
  • Instant marking
  • No sign-up needed
20 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

A lever lifts a load of 600 N when an effort of 150 N is applied to it.

What is the mechanical advantage of the lever?

Choose your answer.

  • 0.25
  • 4
  • 450
  • 750

Model answer

4

Explanation

Mechanical advantage = load ÷ effort = 600 ÷ 150 = 4. It is a ratio of two forces, so it has no units. A mechanical advantage greater than 1 means the lever magnifies the effort; a common mistake is to divide the effort by the load, which gives 0.25.

Mark scheme
  1. 1 mark

    4

    If more than one option is given, 0 marks. 0.25 is wrong: it is effort divided by load (the calculation upside down). 450 is wrong: it is the load minus the effort. 750 is wrong: it is the load plus the effort.

Question 2

3 marks

Mo uses a 1.5 m steel bar as a first order lever to lift one edge of a heavy paving slab. A brick under the bar acts as the fulcrum.

Explain how moving the brick closer to the slab affects the effort Mo needs and the distance Mo's hands must move.

Model answer

Moving the brick closer to the slab makes the distance from the fulcrum to the slab shorter and the distance from the fulcrum to Mo's hands longer. By the principle of moments, effort × its distance equals load × its distance, so with a longer effort distance Mo needs less effort to lift the slab - the mechanical advantage increases. However, Mo's hands now have to move a greater distance to lift the edge of the slab by the same height, so force is gained but distance is lost.

Explanation

Moving the fulcrum towards the load increases the mechanical advantage but also increases the distance the effort must move: a lever never gives more force without costing more movement. Many students explain the effort correctly but forget the second part of the question about distance.

Mark scheme
  1. 1 mark

    The distance from the fulcrum to the load gets shorter and the distance from the fulcrum to Mo's hands gets longer

    Award 1 mark for each valid point; a point explained in detail can earn 2 marks. max 3.

  2. 1 mark

    so less effort is needed / the mechanical advantage increases, because effort × its distance must equal load × its (now shorter) distance (principle of moments)

    Accept 'a smaller force is needed to lift the slab' with a reason based on the distances.

  3. 1 mark

    but Mo's hands must move a greater distance to lift the slab by the same height

    Accept 'the end of the bar must be pushed further down for the same lift'.

  4. 1 mark

    the load end moves a smaller distance for each movement of the hands / force is gained but distance is lost / the work done stays about the same

    Accept all other valid responses.

Question 3

4 marks

Name the type of movement made by each of these parts when the product is in use. Choose from linear, rotary, reciprocating and oscillating.

1. The blades of an electric food blender
2. A sliding patio door as it is opened
3. The handle of a bicycle pump as the pump is used
4. The seat of a child's playground swing

Model answer

1. Rotary
2. Linear
3. Reciprocating
4. Oscillating

Explanation

Rotary motion is turning in a circle (blender blades); linear motion is in one direction in a straight line (the door opening); reciprocating motion is backwards and forwards in a straight line (the pump handle); oscillating motion is to and fro along an arc about a pivot (the swing). Use the technical terms: answers such as 'back and forth' or 'swinging' do not score.

Mark scheme
  1. 1 mark

    1. Rotary

    One mark for each correct type of movement. Only the four named types of movement are credited: descriptions such as 'round and round', 'back and forth', 'up and down', 'sideways' or 'swinging' gain no marks. If more than one type is given for a part, 0 marks for that part. Accept rotation / rotational / rotating for rotary.

  2. 1 mark

    2. Linear

    Do not accept reciprocating: the door moves in one direction in a straight line as it is opened.

  3. 1 mark

    3. Reciprocating

    Accept reciprocation. Do not accept linear or oscillating: the handle is pushed in and pulled out repeatedly along a straight line.

  4. 1 mark

    4. Oscillating

    Accept oscillation. Do not accept reciprocating: the seat swings to and fro along an arc about the top bar.

Question 4

6 marks

Two garden cutting tools are described below. Both use first order levers.

Hedge shears: blades 250 mm long from the pivot and handles 250 mm long from the pivot. Used to trim soft green shoots on hedges, often for long periods.

Pruning loppers: blades 80 mm long from the pivot and handles 600 mm long from the pivot. Used to cut through branches up to 40 mm thick.

Analyse and evaluate how the lever design of each tool suits the task it is used for. In your answer consider the force at the blades and the distances that the handles and blades move.

Model answer

The hedge shears have handles and blades of the same length, 250 mm, so at the blade tips the cutting force is roughly equal to the effort - a mechanical advantage of about 1. This is not a problem, because soft green shoots need very little force to cut. The advantage of equal lengths is movement: the blade tips move as far and as fast as the user's hands, so every time the handles close the blades make a long cut, and a large area of hedge can be trimmed quickly. The shears are also compact and light, which matters because hedge trimming can go on for a long time. However, the force is too low to cut through thick woody stems, except very close to the pivot where the mechanical advantage is higher.

The loppers have handles 600 mm long and blades only 80 mm long, so the handles are 7.5 times longer. This gives a mechanical advantage of about 7.5, so a moderate effort produces a very large force at the jaws, which is needed to cut a branch up to 40 mm thick. The disadvantage is that the handles must move about 7.5 times further than the jaws, so the user has to open their arms wide, needs space around the tool and cuts slowly. This is acceptable because loppers are used for a few heavy cuts, not hundreds of light ones, and the long handles also give extra reach into a tree.

Overall, each tool's lever design is a sensible trade-off between force and movement for its task. The loppers would be far too slow and tiring for trimming a hedge, and the shears could not produce enough force to cut thick branches, so neither tool could do the other's job well.

Explanation

Top-level answers analyse both tools using the distances (equal arms for the shears, a ratio of 7.5 for the loppers), explain the force-versus-movement trade-off and then make clear judgements about suitability. Answers that only describe the tools, or discuss one tool, stay in the lower levels. Avoid vague claims such as 'stronger' or 'easier' without linking them to the lever distances.

Mark scheme
  1. 6 marks

    Levels of response (6 marks).
    Level 3 (5-6 marks): Thorough analysis and evaluation of both the hedge shears and the pruning loppers considering how the lever design of each suits its task (the force at the blades and the distances the handles and blades move).
    Level 2 (3-4 marks): Good analysis and simple evaluative points of one or more of the tools considering how the lever design suits its task.
    Level 1 (1-2 marks): Basic analysis of one or two simple points about the lever design for either tool.
    0 marks: No response or nothing worthy of credit.

    Indicative content (illustrative, not exhaustive; credit any worthy points made in support of the band descriptors): Analysis: identification of how the distances from the pivot affect force and movement in each tool. Evaluation: judgement on how well each tool suits its task, with reasons. Hedge shears: handles and blades the same length, so at the blade tips the cutting force is about the same as the effort (mechanical advantage about 1); the force is greater nearer the pivot, so thicker stems are cut close to the pivot; the blade tips move as far and as fast as the handles, so each closing gives a long cut and a large area of hedge is trimmed quickly; soft green shoots need little force, so a high mechanical advantage is not needed; the short handles keep the tool compact and light, which suits long periods of use; but the shears could not cut a thick branch. Loppers: handles 600 ÷ 80 = 7.5 times longer than the blades, so the force at the jaws is about 7.5 times the effort; a large force is needed to cut a 40 mm branch, so this suits the task; but the handles must move about 7.5 times as far as the jaws, so the user needs space and opens their arms wide; cutting is slow, which is acceptable because only a few cuts are made; long handles also give extra reach into a tree or bush; the tool is larger and heavier. Judgements, e.g. each tool's lever design is a sensible trade-off between force and movement for its task; loppers would be far too slow and tiring for trimming a hedge, and shears could not produce enough force to cut thick branches; neither tool suits the other's job. Accept all other valid responses.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.