Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
AQA GCSE Design and Technology Smart practice A mixed round aimed at your weak spots
Unit 1
Core technical principles
Unit 2
Specialist technical principles
Unit 3
Designing and making principles
Investigation, primary and secondary data
Investigation, primary and secondary data
Environmental, social and economic challenge
Environmental, social and economic challenge
Design strategies
Design strategies
Communication of design ideas
Communication of design ideas
Prototype development
Prototype development
Selection of materials and components
Selecting materials and components for prototypes
Specialist tools and equipment
Specialist tools and equipment
Avg
score:
–
Topics
done:
0/40

Forces and stresses

Practise 20 exam-style questions on Forces and stresses for AQA GCSE Design and Technology. Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 20 questions
  • 1–8 marks each
  • Instant marking
  • No sign-up needed
20 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

2 marks

A tailor is making the waistband of a pair of wool trousers.

Explain why a layer of fusible interfacing is ironed onto the inside of the waistband.

Model answer

The interfacing adds a stiff supporting layer, so the waistband stays firm and flat and does not roll over or crease when the trousers are worn. It also reinforces the area around the button and buttonhole, so the wool can resist the pulling force when the waistband is fastened without stretching out of shape or tearing.

Explanation

Interfacing is an extra layer, woven, knitted or non-woven, applied to the inside of parts of a garment that must hold their shape or take strain, such as waistbands, collars, cuffs and button stands. Fusible interfacing has a heat-activated adhesive on one side, so it is ironed on. Good answers say what force or problem the interfacing resists.

Mark scheme
  1. 1 mark

    It adds a stiffening / supporting layer so the waistband stays firm and keeps its shape, without rolling over, folding or creasing

    Award 1 mark for each valid point. max 2.

  2. 1 mark

    It reinforces the fabric where the button, buttonhole or hook and bar are, so it resists the tension (pulling) when the trousers are fastened and worn and does not stretch out of shape or tear

    Accept 'it stops the wool stretching around the waist'. Accept that, being fusible, it is bonded by heat to the fabric so it cannot move and needs no extra stitching. Accept all other valid responses.

Question 2

3 marks

A designer is making a curved seat for a chair. The seat could be cut to shape from a thick solid board of beech, or made by gluing thin beech veneers together over a curved former (lamination).

Explain why the laminated seat would be stronger.

Model answer

If the curve is cut from a solid board, the grain runs straight across the board, so parts of the curve are left with short grain. Short grain is weak and can split along the grain when the seat bends under the user's weight. In the laminated seat each thin veneer is bent over the former, so the grain follows the curve along the whole length of the seat. The veneers are glued into one piece, and the glue lines add strength and stop any crack spreading, so the seat is much stronger in bending and also keeps its shape.

Explanation

Timber is strongest along its grain, so the key idea is grain direction: lamination makes the grain follow the curve, while cutting from solid leaves weak short grain. Good answers link this to the bending force from the user's weight. Simply saying 'it has more layers so it is stronger' is too vague.

Mark scheme
  1. 1 mark

    Cutting a curve from a solid board leaves short grain across parts of the curve

    Award 1 mark for each valid point; a point explained in detail can earn 2 marks. max 3.

  2. 1 mark

    Short grain is weak and can split or snap along the grain when the seat is bent by the user's weight

  3. 1 mark

    In the laminated seat each veneer is bent to the curve, so the grain follows the curve along the whole length of the seat

    Accept 'the grain runs the full length of the curve, so there is no short grain'.

  4. 1 mark

    The many glued layers act together; the glue lines add strength and stop a crack spreading through the seat

    Accept that the veneers can be laid with their grain in different directions for stability (as in plywood), or that the laminated seat keeps its shape and is less likely to warp or spring back. Accept all other valid responses.

Question 3

4 marks

Name the main type of force acting on each of these parts when the product is in use.

1. The steel cable that holds up a hanging light
2. The legs of a wooden stool when someone sits on it
3. The shaft of a screwdriver as it turns a tight screw
4. A sheet of paper between the blades of a pair of scissors as it is cut

Model answer

1. Tension
2. Compression
3. Torsion
4. Shear

Explanation

The cable is pulled by the weight of the light (tension); the stool legs are squashed by the person's weight (compression); the screwdriver shaft is twisted between the handle and the screw (torsion); and scissor blades push the paper in opposite directions across a line, so it shears. Exam answers must use these technical terms - 'gravity' or 'pulling' will not score.

Mark scheme
  1. 1 mark

    1. Tension

    One mark for each correct force. Only the forces named in the specification are credited: tension, compression, bending, torsion and shear (accept tensile, compressive, torsional, shearing). Weight, gravity, friction or descriptions such as 'pulling', 'squashing' or 'twisting' alone gain no mark. If more than one force is given for a part, mark the first.

  2. 1 mark

    2. Compression

    Do not accept bending as the main force for the legs.

  3. 1 mark

    3. Torsion

    Do not accept shear.

  4. 1 mark

    4. Shear

    Accept shearing. Do not accept tension or torsion.

Question 4

6 marks

A designer is choosing between two steel brackets to support a shelf that will carry heavy books.

Bracket A: an L-shape bent from mild steel flat bar 25 mm wide and 5 mm thick, with the 25 mm width flat against the wall and under the shelf.

Bracket B: an L-shape folded from 1.5 mm mild steel sheet, 25 mm wide, with both long edges folded at 90° to form 10 mm flanges, and a triangular stiffening rib pressed into the corner.

Analyse and evaluate both brackets in terms of how well they resist the forces acting on them.

Model answer

When the shelf is loaded, the weight of the books bends the horizontal arm of each bracket downwards. The bending is greatest at the corner, where the arm tries to droop and close up the angle between the two arms, and the top screws are pulled out of the wall in tension while all the screws carry shear.

Bracket A is a solid, thick bar, so it is robust, simple to make by bending and will not dent. However, its 25 mm width is flat against the wall and the shelf, so in the direction of bending it is only 5 mm deep. A shallow section bends easily, so under heavy books the arm may sag and the angle at the corner may slowly close, letting the shelf tilt forwards. It also uses a lot of steel, making it heavy.

Bracket B is much thinner, but the folded flanges turn the sheet into a channel about 11.5 mm deep. Because stiffness depends so much on depth, the channel is roughly three times as stiff as the flat bar, so it sags far less, while using only about half as much steel. The pressed rib in the corner works like a gusset: it triangulates the corner so the angle between the arms cannot change. Its weaknesses are that thin sheet can dent or buckle if it is knocked or badly overloaded, the screw holes could tear in thin metal, and any corrosion is more serious, so a good finish such as powder coating is needed.

Overall, Bracket B is the better design for heavy books: it gets its stiffness from its shape rather than from the amount of steel, so it is both stiffer and lighter. Bracket A would only match it if it were made much thicker or fitted with a gusset of its own.

Explanation

Top-level answers first identify the forces (bending of the arm, the corner angle closing up, tension and shear in the screws) and then judge each bracket against them, recognising that depth of section and triangulation matter more than thickness of material. Answers that just say 'A is thicker so it is stronger' have not analysed the forces. A clear final judgement is needed for Level 3.

Mark scheme
  1. 6 marks

    Levels of response (6 marks).
    Level 3 (5-6 marks): Thorough analysis and evaluation of both brackets considering how well each resists the forces acting on it when the shelf is loaded.
    Level 2 (3-4 marks): Good analysis and simple evaluative points of one or more of the brackets considering the forces acting on it.
    Level 1 (1-2 marks): Basic analysis of one or two simple points about the forces on either bracket.
    0 marks: No response or nothing worthy of credit.

    Indicative content (illustrative, not exhaustive; credit any worthy points made in support of the band descriptors): Analysis: identification of the forces on the bracket and of how each design resists them. Evaluation: judgement on which bracket performs better and why. Forces: the weight of the shelf and books bends the horizontal arm downwards (the top of the arm is in tension and the bottom in compression); the bending is greatest at the corner, where the horizontal arm tries to droop and close up the angle between the arms; the top screws are pulled out of the wall (tension) and all the screws carry shear; the lower part of the upright arm presses against the wall (compression). Credit any recognition that the corner bends or its angle changes under the load. Bracket A: thick, solid bar, simple to make by bending; robust and will not dent or buckle; but with the bar flat, the section is only 5 mm deep in the direction of bending, so it can flex, the arm can droop and the corner angle can close under a heavy load; uses a lot of steel (heavier and more costly in material). Bracket B: the flanges turn the thin sheet into a channel section about 11.5 mm deep, so it is much stiffer in bending (roughly three times as stiff, and about as strong) while using only about half as much steel; the pressed rib triangulates the corner like a gusset, so the angle between the arms does not change; lighter and cheaper in material and suits mass production by pressing; but thin sheet can dent or buckle locally if overloaded or knocked, screw holes in thin sheet can tear, edges must be deburred, and corrosion through thin metal is more serious, so a good finish is needed; press tools are expensive for small batches. Judgements, e.g. Bracket B resists the bending forces better and is lighter because its strength comes from its shape (flanges and rib); Bracket A would need to be thicker or used on edge to match it. Accept all other valid responses.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.