Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
AQA GCSE Design and Technology Smart practice A mixed round aimed at your weak spots
Unit 1
Core technical principles
Unit 2
Specialist technical principles
Unit 3
Designing and making principles
Investigation, primary and secondary data
Investigation, primary and secondary data
Environmental, social and economic challenge
Environmental, social and economic challenge
Design strategies
Design strategies
Communication of design ideas
Communication of design ideas
Prototype development
Prototype development
Selection of materials and components
Selecting materials and components for prototypes
Specialist tools and equipment
Specialist tools and equipment
Avg
score:
–
Topics
done:
0/40

Linkages, cams and followers

Practise 20 exam-style questions on Linkages, cams and followers for AQA GCSE Design and Technology. Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 20 questions
  • 1–8 marks each
  • Instant marking
  • No sign-up needed
20 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

Through what angle does a bell crank change the direction of a movement?

Choose your answer.

  • 45°
  • 90°
  • 180°
  • 360°

Model answer

90°

Explanation

A bell crank is an L-shaped lever pivoted at its corner, with its arms at right angles. A push or pull on one arm turns it about the pivot, and the other arm then pushes or pulls at 90° to the input, which is how it turns a movement round a corner. A movement turned through 180° (reversed) is produced by a reverse motion linkage.

Mark scheme
  1. 1 mark

    90°

    If more than one option is given, 0 marks. 45° is wrong: the two arms of a bell crank are at right angles to each other. 180° is wrong: reversing the direction is what a reverse motion linkage does. 360° is wrong: that would leave the direction unchanged.

Question 2

2 marks

In a wooden toy, a snail cam lifts a woodpecker's head 18 mm during each turn and then lets it drop suddenly, so that the beak taps the 'tree'. The cam turns at 30 revolutions per minute.

Calculate the total distance the head travels, up and down, in one minute.

Give your answer in mm.

Model answer

In each turn the head rises 18 mm and drops 18 mm.
Distance per turn = 18 + 18 = 36 mm
Distance in one minute = 36 × 30 = 1080 mm

Explanation

Each turn of a snail cam gives one gradual rise followed by one sudden drop of the same size, so the follower travels twice the rise in every turn. Multiply by the number of turns in a minute. The most common error is to count only the upward movement (540 mm).

Mark scheme
  1. 1 mark

    Distance in one turn = 18 + 18 = 36 (mm) / 18 × 2 × 30 seen

    Award full marks for a correct answer, even with no working shown. 540 (18 × 30, the upward movement only) scores 1 mark.

  2. 1 mark

    36 × 30 = 1080 (mm)

    ft their distance per turn × 30. Mark the number, not the units. Accept 1.08 m if the unit is clearly given.

Question 3

3 marks

The output arm of a bell crank is 60 mm long, from the pivot to the end of the arm. The bell crank turns through an angle of 30°.

Calculate the distance moved by the end of the output arm along its arc.

Give your answer in mm to one decimal place.

Model answer

The end of the arm moves along a circle of radius 60 mm.
Circumference = 2 × π × 60 = 377.0 mm
Fraction of a full turn = 30 ÷ 360 = 1/12
Distance moved = 377.0 ÷ 12 = 31.4 mm

Explanation

The end of the arm moves along an arc, which is a fraction of a full circle: 30° is 30/360 = 1/12 of a turn. So the distance is one twelfth of the circumference of a circle whose radius is the arm length. A common error is to treat the 60 mm arm as a diameter, which halves the answer.

Mark scheme
  1. 1 mark

    Circumference of the circle traced by the end of the arm = 2 × π × 60 = 377 (mm)

    Award full marks for a correct answer, even with no working shown. Accept π × 120. Accept [376.8, 377.2] for the circumference (π = 3.14, 3.142 or 22/7 used).

  2. 1 mark

    × 30 ÷ 360 (or ÷ 12)

    ft their circumference × 30/360. Accept 30/360 = 1/12 seen.

  3. 1 mark

    = 31.4 (mm)

    Accept 31.4 only for this mark: the question asks for one decimal place, and π = 3.14, 3.142, 22/7 or the calculator value all give 31.4. An answer not given to one decimal place (e.g. 31.42, 31.43 or 31.416) scores the first two marks only. Mark the number, not the units. 15.7 (using 60 as the diameter: π × 60 ÷ 12) scores 1 mark for the fraction 30/360 used.

Question 4

6 marks

A designer is developing a hand-cranked wooden toy for children aged 5 to 8. When the handle is turned, a model fish rises slowly out of painted 'waves' and then drops suddenly back into them. Two cam mechanisms are being considered.

Design 1: an eccentric cam with a flat follower
Design 2: a snail (drop) cam with a knife-edge follower

Analyse and evaluate both designs for this toy.

Model answer

Design 1 uses an eccentric cam: a circular cam turning on an off-centre shaft. This gives a smooth, continuous rise and fall, with the rise and fall taking the same time and no sudden drop, so the fish would just bob gently up and down. That does not meet the main requirement of a slow rise and a sudden drop. Its advantages are that it works whichever way the handle is turned, so a young child cannot jam it by turning backwards, it is quiet, and it is cheap and easy to make by drilling a wooden disc off-centre. The flat follower has a large contact area, so it wears the wooden cam less than a pointed follower, although it causes more friction than a roller would.

Design 2 uses a snail cam, which lifts the follower gradually through almost the whole turn and then lets it drop suddenly off a step. This is exactly the movement needed: the fish rises slowly and then splashes back into the waves, which children would find fun. However, a snail cam must only turn one way. Children aged 5 to 8 are likely to turn the handle backwards, and the follower would then hit the step and jam, possibly breaking the toy. The knife-edge follower would follow the sharp drop accurately, but its narrow edge would wear quickly and dig into a wooden cam, and the sudden impact adds wear and noise.

Overall, Design 2 is the better choice because only it gives the movement the toy needs. I would improve it by using a small roller follower, which reduces friction and wear while still dropping off the step, and by adding a simple ratchet so that the handle can only turn one way. Design 1 is more robust but fails the main requirement of the toy.

Explanation

Top-level answers analyse the movement each cam gives against the brief (slow rise, sudden drop), consider practical issues such as turning direction, follower wear and the age of the users, and finish with a reasoned judgement, ideally suggesting improvements. Answers that only describe the cams, or deal with one design, stay in Level 1 or 2. Remember that a snail cam's one-way action is a real risk with young children.

Mark scheme
  1. 6 marks

    Levels of response (6 marks).
    Level 3 (5-6 marks): Thorough analysis and evaluation of both cam designs considering how well each would produce the required movement and suit the toy and its young users.
    Level 2 (3-4 marks): Good analysis and simple evaluative points of one or more of the designs considering the movement produced and the suitability for the toy.
    Level 1 (1-2 marks): Basic analysis of one or two simple points about the movement or suitability for either design.
    0 marks: No response or nothing worthy of credit.

    Indicative content (illustrative, not exhaustive; credit any worthy points made in support of the band descriptors): Analysis: identification of the movement each cam and follower would give and of practical features (direction of turning, wear, friction, noise, making). Evaluation: judgement on which design better suits the toy and its users, with reasons and possible improvements. Design 1: an eccentric cam gives a smooth, continuous rise and fall taking equal times, with no dwell and no sudden drop, so the fish would bob up and down rather than rise slowly and drop - it does not meet the brief; it works in either direction, so it cannot jam if a child turns the handle backwards; quiet and smooth; easy and cheap to make (a disc drilled off-centre); a flat follower has a larger contact area, so less wear on a wooden cam, and is robust, but has more friction than a roller. Design 2: a snail cam gives exactly the required slow rise and sudden drop, and the drop gives a satisfying splash or tap, so it meets the brief; but it must only turn one way - if a young child turns the handle backwards the follower hits the step and jams, which could break the toy (a ratchet, one-way clutch or a handle that slips would be needed); a knife-edge follower follows the profile and the sharp drop accurately, but its small contact area wears quickly, digs into a wooden cam and has high friction, so a roller follower might be better; the snail profile is harder to cut accurately (template, laser cutter or CNC); the sudden drop causes impact and noise and wear on the parts. Judgements, e.g. Design 2 is the better choice because only it gives the required movement, but it should be modified with a roller follower and a one-way ratchet to suit young children; Design 1 is more robust but fails the main requirement. Accept all other valid responses.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.