Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
AQA GCSE Design and Technology Smart practice A mixed round aimed at your weak spots
Unit 1
Core technical principles
Unit 2
Specialist technical principles
Unit 3
Designing and making principles
Investigation, primary and secondary data
Investigation, primary and secondary data
Environmental, social and economic challenge
Environmental, social and economic challenge
Design strategies
Design strategies
Communication of design ideas
Communication of design ideas
Prototype development
Prototype development
Selection of materials and components
Selecting materials and components for prototypes
Specialist tools and equipment
Specialist tools and equipment
Avg
score:
–
Topics
done:
0/40

Commercial processes and quality control

Practise 22 exam-style questions on Commercial processes and quality control for AQA GCSE Design and Technology. Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 22 questions
  • 1–8 marks each
  • Instant marking
  • No sign-up needed
20 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

In a woven fabric, which yarns run along the length of the fabric, parallel to the selvedge?

Choose your answer.

  • Weft
  • Bias
  • Pile
  • Warp

Model answer

Warp

Explanation

On a loom the warp yarns are held under tension along the length of the fabric. In each cycle the loom lifts some warp yarns to make a gap (shedding), passes a weft yarn across through the gap (picking) and pushes the weft into place with the reed (beating up). A common mistake is to mix up warp and weft.

Mark scheme
  1. 1 mark

    Warp

    If more than one option is given, 0 marks. Weft is wrong: weft yarns run across the fabric, from selvedge to selvedge, at 90° to the warp. Bias is wrong: it is the direction at 45° to the warp and weft, not a set of yarns. Pile is wrong: pile yarns stand up from the surface of fabrics such as velvet or towelling.

Question 2

3 marks

A textile company is printing a repeating floral pattern onto 2,000 m of cotton fabric. Before production, the customer approved a printed sample of the design.

Describe how the company checks the printed fabric against the original approved sample to make sure the pattern is accurate.

Model answer

The company measures the length of the pattern repeat on the printed fabric and compares it with the repeat on the approved sample, to check it is exactly the same size. It checks that each colour is in register, with no gaps or overlaps, and that the pattern runs straight along the fabric. The colours are compared side by side with the sample in a colour assessment cabinet under standard lighting. These checks are repeated at the start, middle and end of the roll, and the run is stopped if a fault appears.

Explanation

Checking a repeating print against an original sample is a measurable quality control for textiles: the repeat size, registration and colour must all match. Detailed answers say what is measured or compared and how. A common mistake is to describe checking the fabric for holes or stains, which is not the focus of the question.

Mark scheme
  1. 1 mark

    measure the length (and width) of the pattern repeat on the production fabric and compare it with the repeat on the sample, so the repeat is the correct size

    Award 1 mark for each creditworthy point. A point described in detail earns 2 marks. max 3.

  2. 1 mark

    check the colours line up (are in register), with no gaps, overlaps or blurred edges, and that the pattern runs straight along the fabric (not skewed to the selvedge)

  3. 1 mark

    compare the colours side by side with the sample in a colour assessment cabinet (light box) under standard lighting (e.g. artificial daylight), and under other light sources to check the colours still match

    Accept 'compare under the same light' or 'use a spectrophotometer'.

  4. 1 mark

    take samples at regular intervals along the roll (e.g. start, middle and end) and stop the run to correct any faults

    Do not credit 'look at it' alone without saying what is compared. Accept all other valid responses.

Question 3

4 marks

Name a suitable commercial process for making each of these products.

Product 1: 20,000 pizza box nets cut and creased from corrugated card
Product 2: 5,000 identical beech staircase spindles with a curved profile along their length
Product 3: 10,000 aluminium alloy gearbox housings with complex shapes
Product 4: 50,000 printed circuit boards with surface mount components

Model answer

Product 1: die cutting
Product 2: turning on a CNC (or copy) lathe
Product 3: die casting
Product 4: pick and place assembly

Explanation

Each product needs the commercial process for its material category at high volume: die cutting cuts and creases card nets in one press stroke; turning produces round, profiled timber parts; casting gives complex metal shapes in one operation; and pick and place machines position surface mount components on PCBs before soldering. A common mistake is to give a workshop process, such as laser cutting or hand soldering, that is too slow for these quantities.

Mark scheme
  1. 1 mark

    Product 1: die cutting (with a steel rule die / cutting and creasing forme)

    One mark for each suitable process. Do not accept 'cutting' or 'laser cutting' (too slow for 20,000) or 'scissors/craft knife'. Accept 'die cutting and creasing'.

  2. 1 mark

    Product 2: turning (on a CNC lathe or copy lathe / duplicating lathe)

    Accept 'wood turning' or 'CNC turning'. Do not accept 'routing', 'milling' or 'carving' (they do not produce round, profiled spindles efficiently).

  3. 1 mark

    Product 3: casting (e.g. pressure die casting / sand casting)

    Accept 'die casting', 'sand casting', 'gravity die casting'. Accept 'casting then machining'. Do not accept 'injection moulding' (polymers) or 'milling' alone.

  4. 1 mark

    Product 4: pick and place assembly (followed by reflow soldering)

    Accept 'pick and place' or 'automated pick and place'. Accept 'flow soldering / reflow soldering' only if pick and place is also given, as soldering does not place the components. Do not accept 'hand soldering'.

Question 4

6 marks

Choose one of these commercial processes and products:
- Papers and boards: die cutting the nets for 10,000 printed cardboard cartons
- Timber based materials: CNC routing a recessed handle and a decorative edge profile on 1,000 solid oak drawer fronts
- Metal based materials: CNC milling a pocket and two slots in 500 aluminium blocks
- Polymers: extrusion of uPVC pipe
- Textile based materials: rotary screen printing a four-colour pattern onto cotton fabric
- Electronic and mechanical systems: pick and place assembly of surface mount components onto PCBs

Describe, in a logical sequence, how your chosen process is carried out.

Model answer

Extrusion of uPVC pipe.

1. uPVC compound, in powder or granule form, is loaded into the hopper at the back of the extruder.
2. It falls into a long heated barrel. A rotating screw carries it forward, compressing it, and heat from the heater bands and friction melts it.
3. At the front of the barrel the screw forces the molten uPVC through a die with a ring-shaped opening. A mandrel in the centre of the die forms the hole, so the polymer comes out as a continuous tube with the required diameter and wall thickness.
4. The soft pipe passes straight into a sizing unit and a cooling bath of water, which sets it to the correct size.
5. A haul-off unit with caterpillar tracks grips the pipe and pulls it through at a steady speed, so the wall thickness stays even.
6. A saw cuts the pipe to the required length, and the lengths are stacked.
7. Because the process is continuous, the diameter and wall thickness are checked regularly to make sure they stay within tolerance.

Explanation

Level 3 needs the specific stages of the chosen process in the correct order, with the specific equipment for each stage. The best answers name the parts (e.g. die board, creasing rules, ejection rubber; hopper, screw, die, cooling bath, haul-off; stencil, feeders, vision system, reflow oven). A common mistake is to describe a different process, such as injection moulding instead of extrusion, or to give general points with no sequence.

Mark scheme
  1. 6 marks

    Levels of response (6 marks).
    Level 3 (5-6 marks): A detailed description making several correct points for the selected process. Specific correct and appropriate process stages, in a logical sequence, and specific equipment given.
    Level 2 (3-4 marks): A description with points showing some understanding of the selected process. Basic reference made to some stages of the process with some equipment given.
    Level 1 (1-2 marks): Simple notes showing limited understanding of the selected process.
    0 marks: No response or nothing worthy of credit.

    Indicative content (illustrative, not exhaustive; credit any worthy points made in support of the band descriptors). If no process is chosen, mark against the process the answer best fits. Die cutting: net designed in CAD; steel rule die made - a plywood die board with slots cut to hold sharp steel cutting rules (outline), blunt creasing rules (fold lines) and perforating rules if needed; rubber or foam ejection pads beside the rules; die fitted in a flatbed (platen) or rotary press; printed sheets fed in, registered to the print; the press forces the card against the die so it is cut and creased in one stroke; the rubber pushes the card off the rules; waste stripped away; nets stacked, then folded and glued; quality checks of creases and position. CNC routing: CAD drawing; CAM sets toolpaths, cutters (straight cutter for the recess, profile cutter for the edge), speed, feed and depths; blanks located against stops on the vacuum bed (or clamped) at a datum; cutter plunges to depth (Z) and moves in X and Y, often in several passes; tool changer swaps cutters; dust extraction; parts sanded; first-off check. CNC milling: CAD/CAM program; block clamped in a machine vice against a datum; zero set with an edge finder or probe; slot drill or end mill, speed and feed for aluminium; cutting fluid; pocket cleared in layers, then slots cut; parts deburred; checked with gauges or calipers. Extrusion: uPVC compound (powder or granules) fed from the hopper into a heated barrel; rotating screw conveys, compresses and melts it (heat from heaters and friction); melt forced through a die with an annular (ring) opening, with a mandrel forming the hole; pipe drawn through a sizing unit and a cooling water bath; haul-off (caterpillar) pulls it at a steady speed; cut to length by a saw; continuous process; diameter and wall thickness checked. Rotary screen printing: design separated into colours; one cylindrical mesh screen made for each colour, with open areas for that colour; pattern repeat matches the screen circumference; fabric held flat on a moving belt (blanket); print paste fed inside each screen; a squeegee inside the rotating screen forces paste through the open mesh onto the fabric; screens set in register so the colours line up; fabric dried and the colours fixed (steam or heat), then washed; checked against the approved sample. Pick and place: solder paste printed onto the pads through a stencil with a squeegee and inspected; components loaded on tape reels or trays in feeders; machine programmed with placement data from CAD; vacuum nozzles pick each component; camera vision checks its position and orientation; component placed on its pads at the programmed coordinates; boards conveyed to a reflow oven where the paste melts and solders the joints; automatic optical inspection. Accept all other valid responses.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.