Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
AQA GCSE Engineering Smart practice A mixed round aimed at your weak spots
Unit 1
Engineering materials
Unit 2
Engineering manufacturing processes
Additive manufacturing
Additive manufacturing
Material removal
Material removal
Casting and moulding
Casting and moulding
Joining and assembly
Joining and assembly
Heat and chemical treatment
Heat and chemical treatment
Surface finishing
Surface finishing
Unit 3
Systems
Unit 4
Testing and investigation
Unit 5
The impact of modern technologies
Unit 6
Practical engineering skills
Avg
score:
–
Topics
done:
0/32

Surface finishing

Practise 13 exam-style questions on Surface finishing for AQA GCSE Engineering. Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 13 questions
  • 1–8 marks each
  • Instant marking
  • No sign-up needed
13 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

A steel tap is to be electroplated with chromium.

How is the steel tap connected in the electroplating tank?

Choose your answer.

  • A As the anode (positive electrode)
  • B As the cathode (negative electrode)
  • C To an earth wire only
  • D It is not connected; it hangs freely in the solution

Model answer

B As the cathode (negative electrode)

Explanation

In electroplating, the object to be plated is made the cathode (negative). Positive metal ions in the solution are attracted to it and are deposited as a thin metal layer. A common mistake is to choose the anode, which is the positive electrode (often a bar of the plating metal).

Mark scheme
  1. 1 mark

    B / As the cathode (negative electrode)

    Accept the letter or the option text. If more than one option is given, 0 marks.

Question 2

2 marks

The steel handlebars of a child's bicycle are chrome plated.

Give two reasons why chrome plating is used for the handlebars.

Model answer

1. It protects the steel from rusting when the bicycle is left out in the rain.
2. It gives a bright, shiny finish that looks attractive.

Explanation

Chrome plating puts a thin, hard layer of chromium on the steel by electroplating. It protects against corrosion, looks bright and resists wear, and it is easy to wipe clean. It does not make the handlebars stronger, because the strength comes from the steel tube.

Mark scheme
  1. 2 marks

    Any two different reasons: protects the steel from corrosion/rust / gives an attractive, bright, shiny appearance / gives a hard surface that resists wear and scratching / is easy to clean / is smooth to touch

    1 mark for each different correct reason, max 2. Do not accept 'cheap' (it is not), 'makes it stronger' or 'waterproof' on its own.

Question 3

3 marks

Use the word bank to complete the statements about hot-dip galvanising.

First, rust and scale are removed by dipping the steel in (a) __________.

The cleaned steel is then dipped into a bath of (b) __________ zinc at about 450 °C.

If the coating is scratched, the steel is still protected because the coating gives (c) __________ protection: it corrodes instead of the steel.

Word bank:   acid   cold   molten   oil   paint   plastic   sacrificial   tin

Give the missing word for (a), (b) and (c).

Model answer

(a) acid
(b) molten
(c) sacrificial

Explanation

Hot-dip galvanising cleans the steel in acid (pickling), then dips it in molten zinc at about 450 °C. Zinc is more reactive than iron, so where the coating is scratched the zinc corrodes first and protects the exposed steel. This is called sacrificial protection, and it is why galvanised steel lasts so long outdoors.

Mark scheme
  1. 1 mark

    (a) acid

    Only the word bank word scores. Do not accept oil.

  2. 1 mark

    (b) molten

    Do not accept cold.

  3. 1 mark

    (c) sacrificial

    Only 'sacrificial' scores.

Question 4

6 marks

A batch of steel wire baskets is to be plastic dip coated using a fluidised bed.

Describe, in stages, how one basket is dip coated.

Include the equipment used and any safety precautions.

Model answer

1. Clean the basket with a degreaser and remove any rust with wire wool, because the plastic will not stick to dirty or greasy metal.
2. Hang the basket on a wire hook. Wearing heat-resistant gloves, place it in an oven at about 200 °C for several minutes until it is evenly hot all over.
3. Turn on the air supply to the fluidising tank. Air blows up through a porous base and lifts the polyethylene powder so it bubbles and behaves like a liquid. Wear goggles and a dust mask, and keep the extraction on.
4. Lift the hot basket out with tongs and plunge it straight into the fluidised powder for about 3-5 seconds, moving it slightly so every wire is covered. The powder melts as it touches the hot metal and forms a layer.
5. Lift it out and tap it gently to remove loose powder.
6. Put it back in the oven for a few minutes so the plastic fuses (flows together) into a smooth, glossy coating.
7. Hang it up to cool away from other people, then trim off any drips with a knife.

Explanation

A top answer gives the stages in order (clean, preheat, fluidise the powder, dip, remove excess, post-heat, cool), names the equipment (oven, fluidising tank, tongs, hook) and includes safety for both heat and powder. The key idea is that the metal is hot enough to melt the powder, which then sticks to it. A list of steps with no detail is capped at 2 marks.

Mark scheme
  1. 6 marks

    Levels of response (6 marks).
    Level 3 (5-6 marks): Detailed explanation including all key stages to dip coat the basket, with the equipment/tools used and safety. Notes are clear and in a logical order.
    Level 2 (3-4 marks): Some stages described in detail OR the majority of stages covered but with insufficient detail to allow the basket to be correctly coated.
    Level 1 (1-2 marks): One or more basic steps/stages listed.
    0 marks: No response or nothing worthy of credit.

    Max 2 if the stages are only listed with no detail.
    Indicative content (in order; accept all other valid responses):
    - Clean and degrease the basket and remove any rust (emery cloth, wire wool, degreaser) so the plastic will stick.
    - Hang it on a wire hook and heat it in an oven to about 200 °C (accept roughly 180-250 °C) until it is evenly hot.
    - Switch on the air supply to the fluidising tank so the plastic powder (e.g. polyethylene) is lifted by the air and behaves like a liquid.
    - Using tongs or the hook, plunge the hot basket into the fluidised powder for a few seconds, moving it gently; the powder melts and sticks to the hot metal.
    - Lift it out and tap off any loose powder.
    - Return it to the oven for a few minutes so the coating fuses into a smooth, glossy layer.
    - Hang it up to cool, then trim any drips or runs.
    Safety: heat-resistant gloves, tongs, apron, goggles, a dust mask for the fine powder, extraction/ventilation for fumes, keep the powder away from naked flames.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.