Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
AQA GCSE Engineering Smart practice A mixed round aimed at your weak spots
Unit 1
Engineering materials
Unit 2
Engineering manufacturing processes
Additive manufacturing
Additive manufacturing
Material removal
Material removal
Casting and moulding
Casting and moulding
Joining and assembly
Joining and assembly
Heat and chemical treatment
Heat and chemical treatment
Surface finishing
Surface finishing
Unit 3
Systems
Unit 4
Testing and investigation
Unit 5
The impact of modern technologies
Unit 6
Practical engineering skills
Avg
score:
–
Topics
done:
0/32

Heat and chemical treatment

Practise 14 exam-style questions on Heat and chemical treatment for AQA GCSE Engineering. Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 14 questions
  • 1–8 marks each
  • Instant marking
  • No sign-up needed
14 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

Which one of the following properties of high carbon steel is increased when the steel is hardened?

Choose your answer.

  • A Ductility
  • B Hardness
  • C Malleability
  • D Toughness

Model answer

B Hardness

Explanation

Hardening (heating above the upper critical temperature and quenching) makes high carbon steel much harder, so it resists wear, scratching and indentation. The same process makes it brittle: ductility, malleability and toughness all fall, which is why hardened tools are usually tempered.

Mark scheme
  1. 1 mark

    B / Hardness

    Accept the letter or the option text. If more than one option is given, 0 marks.

Question 2

2 marks

High carbon steel parts are sometimes quenched in oil rather than in water when they are hardened.

Explain why oil is used.

Model answer

Oil takes heat away from the steel more slowly than water, so the quench is less severe. This reduces the thermal shock and internal stresses, so the part is less likely to crack or distort, especially if it has thin sections or sharp corners.

Explanation

Quenching must be fast enough to harden the steel, but a very severe quench (water or brine) causes large stresses that can crack or warp the part. Oil still cools quickly enough to harden many steels but more gently. The first mark is for the slower cooling and the second for the consequence.

Mark scheme
  1. 1 mark

    Oil cools the steel less rapidly / less severely than water

    Accept 'oil gives a slower quench' or 'a gentler quench'. Do not accept 'oil is cooler' or 'oil is safer'.

  2. 1 mark

    so there is less risk of the part cracking or distorting (warping) from the sudden temperature change / thermal shock

    Justification linked to the slower cooling. Accept 'less internal stress, so it is less likely to crack'.

Question 3

3 marks

Use the word bank to complete the statements about annealing.

After a steel sheet has been pressed into shape, it becomes harder and may crack if it is pressed again. Annealing makes the steel softer and more (a) __________ again.

Annealing also relieves internal (b) __________ in the metal.

To anneal the steel, it is heated above its upper critical temperature and then cooled very (c) __________.

Word bank:   brittle   ductile   hard   oxides   quickly   slowly   stresses   tempered

Give the missing word for (a), (b) and (c).

Model answer

(a) ductile
(b) stresses
(c) slowly

Explanation

Pressing (cold working) makes steel harder, less ductile and full of internal stresses. Annealing heats the steel above its upper critical temperature and cools it very slowly, usually in the furnace, which gives the softest, most ductile state and removes the stresses so it can be worked again. Cooling quickly would harden the steel instead.

Mark scheme
  1. 1 mark

    (a) ductile

    Only the word bank word scores. Do not accept brittle or hard.

  2. 1 mark

    (b) stresses

    Do not accept oxides.

  3. 1 mark

    (c) slowly

    Do not accept quickly.

Question 4

6 marks

The blade of a screwdriver is made from high carbon steel.

Describe, in stages, how the tip of the blade can be hardened and then tempered in a school workshop.

Include the equipment used and any safety precautions.

Model answer

Hardening
1. Put on a leather apron, gloves and a face shield, and hold the blade in tongs.
2. Heat the last 30-40 mm of the blade in the brazing hearth with a gas torch until it glows cherry red (about 760-800 °C, just above the upper critical temperature). A magnet will no longer be attracted to it.
3. Keep it at that heat for a short time so the tip is heated right through.
4. Plunge it vertically into a tank of cold water and move it up and down so it cools quickly and evenly without warping. Stand back from the steam. The tip is now very hard but brittle.

Tempering
5. Clean the tip with emery cloth until the steel is bright, so the oxide colours will show.
6. Heat the shank gently, a little way behind the tip, so the heat flows along to the tip.
7. Watch the colours move towards the tip: pale straw, dark straw, brown, purple, then blue.
8. When blue (about 300 °C) reaches the tip, quench it in water immediately to stop the tempering.
9. The tip is still hard enough not to wear, but it is tougher, so it will not snap or chip when the screwdriver is twisted. Leave a 'hot work' warning and let the tongs cool safely.

Explanation

A top answer describes both processes in order, with temperatures or colours: heat to cherry red and quench to harden, then clean, reheat gently and watch the oxide colours to temper. It also names the equipment (hearth, torch, tongs, quench tank, emery cloth) and the safety precautions. Common errors are cooling slowly after heating (this anneals the steel) or reheating the tip directly so the colours pass too quickly.

Mark scheme
  1. 6 marks

    Levels of response (6 marks).
    Level 3 (5-6 marks): Detailed explanation including all key stages to harden and temper the screwdriver tip, with the equipment/tools used and safety. Notes are clear and in a logical order.
    Level 2 (3-4 marks): Some stages described in detail OR the majority of stages covered but with insufficient detail to allow the tip to be correctly hardened and tempered.
    Level 1 (1-2 marks): One or more basic steps/stages listed.
    0 marks: No response or nothing worthy of credit.

    Max 2 if the stages are only listed with no detail. Max 4 if only hardening or only tempering is described.
    Indicative content (in order; accept all other valid responses):
    Hardening
    - Heat the end of the blade in a brazing hearth or forge with a gas torch until it is cherry red, just above the upper critical temperature (about 760-800 °C); a magnet no longer attracts steel at about this temperature.
    - Hold it at that temperature briefly so it is heated evenly (soak).
    - Quench it quickly in water (or oil), plunging it in vertically and moving it up and down to avoid distortion and uneven cooling.
    - The tip is now very hard but brittle (a file will skid on it).
    Tempering
    - Clean the tip to bright metal with emery cloth so the oxide colours can be seen.
    - Reheat gently, applying the heat to the shank behind the tip so the colours travel along towards the tip.
    - Watch the colours: pale straw, dark straw, brown, purple, then blue. When blue (about 300 °C) reaches the tip, quench it at once.
    - The tip keeps most of its hardness but is now tougher and less brittle.
    Safety: leather apron and gloves, face shield or goggles, hold the work with tongs, beware of steam and spitting when quenching (and of fire with oil), good ventilation, warn others that the work is hot.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.