Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
AQA GCSE Engineering Smart practice A mixed round aimed at your weak spots
Unit 1
Engineering materials
Unit 2
Engineering manufacturing processes
Additive manufacturing
Additive manufacturing
Material removal
Material removal
Casting and moulding
Casting and moulding
Joining and assembly
Joining and assembly
Heat and chemical treatment
Heat and chemical treatment
Surface finishing
Surface finishing
Unit 3
Systems
Unit 4
Testing and investigation
Unit 5
The impact of modern technologies
Unit 6
Practical engineering skills
Avg
score:
–
Topics
done:
0/32

Casting and moulding

Practise 16 exam-style questions on Casting and moulding for AQA GCSE Engineering. Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 16 questions
  • 1–8 marks each
  • Instant marking
  • No sign-up needed
16 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

Which part of an injection moulding machine pushes the finished moulding out of the mould when it opens?

Choose your answer.

  • A Ejector pins
  • B Hopper
  • C Screw
  • D Sprue

Model answer

A Ejector pins

Explanation

When the mould opens, ejector pins push the moulding off the core, which is why many plastic products have small circular marks on their inside faces. The hopper feeds granules into the barrel, the screw melts and injects the polymer, and the sprue is the channel the molten polymer enters the mould through.

Mark scheme
  1. 1 mark

    A / Ejector pins

    Accept the letter or the option text. If more than one option is given, 0 marks.

Question 2

2 marks

A plastic storage box was made by injection moulding.

Give two features you could look for on the box that show it was injection moulded.

Model answer

1. Small round ejector pin marks on the inside of the box.
2. A thin split line around the outside where the two halves of the mould met.

Explanation

Injection moulding leaves evidence of the mould and its mechanism: ejector pin marks, the split line, and the point where the sprue or gate was cut off. Designers also add draft angles, even wall thicknesses and strengthening ribs so the part fills, cools evenly and ejects easily, so these features also point to injection moulding.

Mark scheme
  1. 2 marks

    Any two from: small circular ejector pin marks / a split (parting) line where the mould halves met / a small sprue or gate mark where the polymer entered / draft angles (slightly tapered sides) / an even wall thickness / ribs, bosses or webs moulded in / fine detail or text moulded into the surface / a smooth, glossy surface finish

    1 mark for each different correct feature, max 2. Do not accept 'it is plastic' or 'it is hollow'.

Question 3

3 marks

An injection mould for a phone case costs £18 000 to make. The material, energy and labour for each case cost 6p.

Calculate the total cost of making each case when a batch of 40 000 cases is made.

Model answer

Mould cost per case = £18 000 ÷ 40 000 = £0.45
6p = £0.06
Cost per case = £0.45 + £0.06 = £0.51

Explanation

The mould is a one-off cost, so it is shared between all the cases made; the 6p is paid for every case. Adding the share of the mould to the running cost gives the cost of each case. Keep the units the same: adding 6 to 0.45 gives the nonsense answer of £6.45.

Mark scheme
  1. 1 mark

    Mould cost per case = 18 000 ÷ 40 000 = £0.45 (45p); or a correct final answer of £0.51 (51p) with no working

    An answer of £0.51 or 51p with no working scores 3 marks.

  2. 1 mark

    Converts 6p = £0.06 (or works in pence: 45p + 6p)

    Independent of the first mark.

  3. 1 mark

    Total per case = 0.45 + 0.06 = £0.51 (51p)

    Allow ECF from their mould cost per case if the units are consistent. £6.45 (pence not converted) scores 1 mark. £20 400 (the total cost of the batch, 18 000 + 40 000 × 0.06, not divided by 40 000) scores the second mark only.

Question 4

6 marks

Describe, in stages, how an aluminium alloy bracket is made by sand casting, starting from a split wooden pattern.

Model answer

1. Put the drag upside down on a flat moulding board and place one half of the split pattern in the middle. Dust it with parting powder so that the sand does not stick.
2. Sieve green sand over the pattern, then ram it firmly into the drag and strike off the excess with a straight edge.
3. Turn the drag over, fit the cope on top, and place the other half of the pattern on its locating pins. Dust with parting powder and position the sprue pin and riser pin.
4. Fill and ram the cope, pull out the sprue and riser pins, and push a vent wire into the sand so gases can escape.
5. Lift off the cope, carefully remove both pattern halves, cut a runner from the sprue to the cavity, and put the cope back on the drag.
6. Melt the aluminium alloy in a crucible in the furnace at about 700 °C. Wearing a leather apron, gauntlets, spats and a face shield, lift the crucible with tongs into a pouring shank, skim off the dross and pour steadily into the sprue until metal rises in the riser. All tools must be dry, as water and molten metal cause explosions.
7. Leave the metal to cool and solidify, then break away the sand to remove the casting.
8. Fettle the casting: saw off the sprue and riser, wire brush off the sand, and file or machine the faces that must be accurate.

Explanation

Top-level answers give the stages in order (drag, ram, cope, sprue and riser, remove pattern, melt and pour, cool, break out, fettle) with the equipment and the safety precautions for molten metal, especially keeping everything dry. Students often mix in features of die casting, such as a steel die or ejector pins. A list of stages with no detail is capped at 2 marks.

Mark scheme
  1. 6 marks

    Levels of response (6 marks).
    Level 3 (5-6 marks): Detailed explanation including all key stages to make the bracket by sand casting, with the equipment/tools used and safety. Notes are clear and in a logical order.
    Level 2 (3-4 marks): Some stages described in detail OR the majority of stages covered but with insufficient detail to allow correct manufacture.
    Level 1 (1-2 marks): One or more basic steps/stages listed.
    0 marks: No response or nothing worthy of credit.

    Max 2 if the stages are only listed with no detail. Indicative content, key stages in order (accept all other valid responses):
    1. Place the drag upside down on a moulding board with one half of the pattern inside; dust with parting powder.
    2. Fill the drag with green (or oil-bonded) sand and ram it firmly around the pattern; strike off the excess level with the top.
    3. Turn the drag over, fit the cope on top with the second half of the pattern, dust with parting powder, and place sprue and riser pins.
    4. Ram the cope with sand, then remove the sprue and riser pins and vent the mould with a wire.
    5. Separate the cope and drag, carefully withdraw the pattern halves, cut a runner and gate from the sprue to the cavity, then reassemble the mould.
    6. Melt the aluminium in a crucible in a furnace (about 700 °C), skim off the dross, and pour steadily into the sprue until metal appears at the top of the riser.
    7. Leave the casting to cool and solidify, then break up the sand mould to remove it.
    8. Fettle the casting: cut off the sprue, runner and riser with a saw, clean off the sand and file or machine the faces that need to be accurate.
    Safety: wear a heat-resistant apron, gauntlets, face shield and spats; preheat tools and keep everything dry, because water meeting molten metal turns to steam explosively; use proper crucible tongs and a pouring shank; work on a sand floor with a clear route; ventilate fumes.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.