Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
AQA GCSE Engineering Smart practice A mixed round aimed at your weak spots
Unit 1
Engineering materials
Unit 2
Engineering manufacturing processes
Additive manufacturing
Additive manufacturing
Material removal
Material removal
Casting and moulding
Casting and moulding
Joining and assembly
Joining and assembly
Heat and chemical treatment
Heat and chemical treatment
Surface finishing
Surface finishing
Unit 3
Systems
Unit 4
Testing and investigation
Unit 5
The impact of modern technologies
Unit 6
Practical engineering skills
Avg
score:
–
Topics
done:
0/32

Structural systems

Practise 14 exam-style questions on Structural systems for AQA GCSE Engineering. Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 14 questions
  • 1–8 marks each
  • Instant marking
  • No sign-up needed
14 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

The drive shaft of a car carries the turning force from the gearbox to the wheels.

Which type of force mainly acts on the drive shaft?

Choose your answer.

  • A Bending
  • B Compression
  • C Tension
  • D Torsion

Model answer

D Torsion

Explanation

Torsion is a twisting force. A drive shaft is twisted by the engine at one end while the wheels resist turning at the other, so it must be designed to resist torsion. Bending makes a member sag, compression squashes it and tension stretches it.

Mark scheme
  1. 1 mark

    D / Torsion

    Accept the letter or the option text. If more than one option is given, 0 marks.

Question 2

2 marks

A rectangular wooden frame for a garden gate changes shape (sags at one corner) when a child swings on it.

Explain why fixing a diagonal brace across the frame stops this happening.

Model answer

The diagonal brace splits the rectangle into two triangles. A rectangle can be pushed into a parallelogram because its joints act like hinges, but a triangle cannot change shape unless one of its sides changes length, so the triangulated frame stays rigid and the gate does not sag.

Explanation

Triangulation is used in gates, bridges, roof trusses, cranes and space frames because a triangle is a rigid shape. The brace becomes a member in compression or tension that resists the frame distorting. 'It makes it stronger' is too vague: the answer must explain why triangles keep their shape.

Mark scheme
  1. 1 mark

    The brace divides the rectangle into triangles (it triangulates the frame)

    Accept 'it makes triangles'.

  2. 1 mark

    A triangle cannot change shape unless one of its sides changes length, so the frame becomes rigid and cannot distort (the brace carries the load in compression or tension)

    Accept 'a rectangle can be pushed into a parallelogram but a triangle cannot'. Do not accept 'it makes it stronger' with no explanation.

Question 3

2 marks

The floor of a new dance studio must be designed for dynamic loads as well as static loads.

Explain why the dynamic loads are important for this floor.

Model answer

When dancers jump and land together, the forces on the floor change quickly and can be several times their static weight. Repeated jumping in time to music also makes the floor vibrate, and if the rhythm matches the floor's natural frequency the bouncing can build up, so the floor must be stiff and strong enough to resist these changing loads without excessive movement or fatigue cracking.

Explanation

A dynamic (live) load is one that moves or changes, such as people walking, jumping or dancing. It can be much bigger than the static weight of the same people, and repeated loads can cause vibration and fatigue. Each well-explained effect of the dynamic load earns a mark.

Mark scheme
  1. 1 mark

    Dancers jumping and landing (moving, stamping in time) produce loads that change quickly and can be much larger than their static weight (impact loads)

    1 mark for each point, max 2. Do not accept 'people move about' with no consequence.

  2. 1 mark

    Repeated rhythmic loads make the floor vibrate (bounce); if they match the floor's natural frequency the vibration builds up (resonance) / repeated loading can cause fatigue, so the floor must be stiff and strong enough not to vibrate excessively or fail

    Accept 'the floor must not bounce or crack under repeated jumping'.

Question 4

6 marks

A road bridge is made from steel beams that span between concrete piers, with a concrete deck on top.

Use notes to explain how the different types of load on the bridge are applied and transmitted through the structure to the ground.

Model answer

1. Dead (static) loads: the weight of the concrete deck, the steel beams, the road surface and the barriers. These act all the time.
2. Imposed loads: the vehicles, people and snow on the bridge. Dynamic (live) loads are those that move or change, such as moving traffic, lorries braking and wind gusts, which can also make the bridge vibrate.
3. All these loads act on the deck, which spreads them onto the steel beams below.
4. Each beam bends (sags) between the piers: its top flange is in compression and its bottom flange is in tension.
5. When a heavy lorry is in one lane, or a strong wind blows from the side, the deck is loaded unevenly and tends to twist (torsion), so the beams are cross-braced to resist this.
6. The beams transfer the loads to the piers at their ends.
7. The concrete piers are in compression; they must be thick enough, or braced, so they do not buckle.
8. The piers pass the loads into the foundations, which spread them over a large area of ground (or carry them down to bedrock on piles), so the bridge does not sink or tilt.

Explanation

A top-level answer names the three types of load with examples and then follows the load path in order: deck, beams (bending, with compression on top and tension underneath), piers (compression, risk of buckling), foundations and ground. Mentioning torsion from uneven loads and how bracing resists it adds detail. Simply listing 'deck, beams, piers, ground' with no forces stays in Level 1.

Mark scheme
  1. 6 marks

    Levels of response (6 marks).
    Level 3 (5-6 marks): Detailed explanation including all key stages of how the loads are applied and transmitted from the deck through the beams and piers to the foundations and ground, naming the types of load (dead, imposed, dynamic) and the forces in each part (bending, tension, compression). Notes are clear and in a logical order.
    Level 2 (3-4 marks): Some stages described in detail OR the majority of stages covered but with insufficient detail to show how the loads are transmitted.
    Level 1 (1-2 marks): One or more basic steps/stages listed.
    0 marks: No response or nothing worthy of credit.

    Max 2 if the stages are only listed with no detail.
    Indicative content (in order; accept all other valid responses):
    - Loads applied: dead (static) load - the self-weight of the deck, beams, road surface and barriers, always present; imposed load - vehicles, people, snow; dynamic (live) load - moving traffic, braking and accelerating vehicles, wind gusts, vibration.
    - The loads act on the deck, which spreads them onto the steel beams.
    - The beams bend (sag) between the piers: the top of each beam is in compression and the bottom is in tension.
    - Off-centre loads (e.g. a lorry in one lane) or crosswinds can twist the deck (torsion); cross-bracing between beams resists this.
    - The beams pass the loads to the piers (and abutments) at their ends.
    - The piers are in compression; tall, slender piers must be designed not to buckle.
    - The piers pass the loads to the foundations, which spread the load over a large area of ground (or onto piles/bedrock) so the ground does not sink.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.