Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
AQA GCSE Engineering Smart practice A mixed round aimed at your weak spots
Unit 1
Engineering materials
Unit 2
Engineering manufacturing processes
Additive manufacturing
Additive manufacturing
Material removal
Material removal
Casting and moulding
Casting and moulding
Joining and assembly
Joining and assembly
Heat and chemical treatment
Heat and chemical treatment
Surface finishing
Surface finishing
Unit 3
Systems
Unit 4
Testing and investigation
Unit 5
The impact of modern technologies
Unit 6
Practical engineering skills
Avg
score:
–
Topics
done:
0/32

Engineering polymers

Practise 15 exam-style questions on Engineering polymers for AQA GCSE Engineering. Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 15 questions
  • 1–8 marks each
  • Instant marking
  • No sign-up needed
15 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

A face shield worn when using a grinder must be transparent and must not shatter if it is hit by a flying fragment of metal.

Which polymer is the most suitable for the face shield?

Choose your answer.

  • A Acrylic
  • B Melamine formaldehyde
  • C Polycarbonate
  • D Polystyrene

Model answer

C Polycarbonate

Explanation

Polycarbonate is transparent and extremely tough, so it absorbs impacts without shattering, which is why it is used for safety glasses, face shields and machine guards. Acrylic is clear but brittle and can crack on impact. Polystyrene is also brittle, and melamine formaldehyde is an opaque thermoset.

Mark scheme
  1. 1 mark

    C / Polycarbonate

    Accept the letter or the option text. If more than one option is given, 0 marks.

Question 2

2 marks

The small gears inside a kitchen food mixer are made from nylon.

Give two reasons why nylon is a suitable material for these gears.

Model answer

Nylon has low friction and is self-lubricating, so the gears run smoothly without oil or grease that could get into the food. It is also hard-wearing, so the gear teeth last a long time.

Explanation

Nylon is one of the best polymers for moving parts because it has low friction, good wear resistance and toughness. It runs more quietly than metal gears and can be injection moulded to accurate shapes in large numbers. Answers such as 'strong' or 'cheap' need a reason to score.

Mark scheme
  1. 2 marks

    Any two from: low friction / self-lubricating, so no oil or grease is needed near food; hard-wearing / good wear resistance; quiet running; tough, so the teeth do not snap; lightweight; can be injection moulded cheaply into accurate gear shapes; does not corrode

    1 mark for each different correct reason, max 2. Low friction and self-lubricating count as the same reason. Do not accept 'strong', 'cheap' or 'easy to make' on their own.

Question 3

3 marks

Use the word bank to complete the statements.

The polymer (a) __________ is a tough thermoplastic with low friction and good wear resistance, so it is used for small gears and bearings.

The polymer (b) __________ is a hard, scratch-resistant thermoset used for picnic plates and for the surface layer of kitchen worktops.

The polymer (c) __________ is a thermoset supplied as a resin and a hardener. It is used as a strong adhesive and as the matrix of carbon-fibre composites.

Word bank:   ABS   acrylic   epoxy resin   melamine formaldehyde   nylon   polycarbonate   polystyrene   vulcanised rubber

Give the missing polymer for each of (a), (b) and (c).

Model answer

(a) nylon
(b) melamine formaldehyde
(c) epoxy resin

Explanation

Nylon's low friction and wear resistance make it ideal for gears, bearings and bushes. Melamine formaldehyde is a hard, heat-resistant thermoset used for tableware and laminates. Epoxy resin cures when it is mixed with a hardener, giving a strong adhesive and the usual matrix for carbon fibre.

Mark scheme
  1. 1 mark

    (a) nylon

    Do not accept ABS or acrylic.

  2. 1 mark

    (b) melamine formaldehyde

    Accept melamine / melamine resin. Do not accept epoxy resin.

  3. 1 mark

    (c) epoxy resin

    Accept epoxy. Each blank is credited separately.

Question 4

6 marks

Describe, in stages, how waste thermoplastic products, such as old ABS casings, are recycled into granules that can be used to make new products.

Model answer

1. The waste products are collected from recycling centres and take-back schemes.
2. They are sorted by type of polymer, using the resin identification code or infrared scanners, so that only ABS goes into the batch, and metal parts such as screws are removed with magnets.
3. The plastic is washed to remove labels, dirt and other contaminants, because these would weaken the new material.
4. It is fed into a granulator, which has guarded rotating blades, and cut into small flakes, which are then dried.
5. The flakes are fed into an extruder, where a heated screw melts the ABS and pushes it through a fine filter and out through a die as thin strands. This works because ABS is a thermoplastic and softens again when heated.
6. The strands are cooled in a water bath and chopped into small, even granules, which are bagged.
7. The granules can then be mixed with new ABS and injection moulded into new products.
Operators wear gloves, eye protection and ear defenders, the shredder has interlocked guards, and fumes from the extruder are extracted.

Explanation

A top-level answer gives every stage in a logical order - collect, sort, clean, shred, melt and extrude, cool, chop into granules - with the equipment and safety at each stage. Sorting is essential because different polymers do not mix. Only thermoplastics can be recycled like this, because they soften when heated; thermosets have cross-links and would char.

Mark scheme
  1. 6 marks

    Levels of response (6 marks).
    Level 3 (5-6 marks): Detailed explanation including all key stages to turn waste thermoplastic products into granules, with the equipment used and safety. Notes are clear and in a logical order.
    Level 2 (3-4 marks): Some stages described in detail OR the majority of stages covered but with insufficient detail to allow correct recycling.
    Level 1 (1-2 marks): One or more basic steps/stages listed.
    0 marks: No response or nothing worthy of credit.

    Max 2 if the stages are only listed with no detail.
    Indicative content, key stages in order (accept all other valid responses):
    1. Collect the waste products (kerbside collection, recycling centres, take-back schemes).
    2. Sort by type of polymer, using the resin identification code / infrared scanners / hand sorting, because different polymers cannot be mixed; remove metal parts such as screws (magnets, eddy current separators).
    3. Wash to remove labels, dirt, paint and other contaminants.
    4. Shred or granulate into small flakes using a shredder or granulator (guarded machine).
    5. Dry the flakes.
    6. Heat to melt the flakes in an extruder, which pushes the molten polymer through a die, often with a filter (screen) to remove any remaining contaminants.
    7. Cool the extruded strands in a water bath.
    8. Chop the strands into small pellets (granules) and bag them.
    9. The granules are reused, often mixed with new (virgin) polymer, in injection moulding or extrusion to make new products.
    Safety: guards and interlocks on shredders, PPE (gloves, eye protection, ear defenders), fume extraction when melting, burns from hot machinery.
    Thermoplastics can be recycled in this way because they soften when reheated; thermosets cannot.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.