Practise 15 exam-style questions on Practical processes, tools and measuring for AQA GCSE Engineering. Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.
15 questions
1–8 marks each
Instant marking
No sign-up needed
15 questions, marked as you go
Sample questions with model answers
Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.
Question 1
1 mark
Which tool is used to cut an external thread on the end of a steel rod?
Choose your answer.
A Countersink bit
B Die, held in a die stock
C Reamer
D Tap, held in a tap wrench
Model answer
B
Explanation
A die cuts an external thread (like the thread on a bolt) and is turned with a die stock. A tap cuts an internal thread in a hole (like the thread in a nut) and is turned with a tap wrench. A reamer finishes a hole to an accurate size, and a countersink bit makes a cone-shaped recess for a screw head.
Mark scheme
1 mark
B / Die, held in a die stock
Accept the letter or the option text. If more than one option is given, 0 marks.
Question 2
2 marks
Explain one reason why swarf should be cleared from a workbench with a brush rather than with bare hands.
Model answer
Swarf, the small chips and curls of metal made by cutting, filing and drilling, has very sharp edges, so it can easily cut your hand or leave splinters of metal in the skin. A brush moves it safely.
Explanation
Swarf is sharp and can be hot, so it should be cleared with a brush, never with bare hands, and never blown away, which can send chips into someone's eyes. This is part of keeping a safe workshop. One mark is for the hazard and one for the injury it could cause.
Mark scheme
1 mark
Swarf has very sharp edges / swarf may still be hot after cutting
Do not accept 'it is dirty' or 'it is untidy'.
1 mark
So it could cut the skin / splinter into the hand / burn the hand
Must be linked to the hazard in the first point.
Question 3
3 marks
A student has welded a rectangular steel frame that should be 500 mm long and 350 mm wide. To check that the corners are square (90°), the student measures the two diagonals of the frame.
Calculate the length that each diagonal should be if the frame is square.
Show your working.
Model answer
Diagonal² = 500² + 350² = 250 000 + 122 500 = 372 500 Diagonal = √372 500 = 610.3 mm If both diagonals measure 610.3 mm the frame is square; if they are different, it is out of square.
Explanation
Each diagonal is the hypotenuse of a right-angled triangle with sides of 500 mm and 350 mm, so Pythagoras gives 610.3 mm. In the workshop the diagonals are measured and compared: equal diagonals show the frame is square, while unequal diagonals show it has been pulled into a parallelogram and should be corrected before the welds are completed.
Mark scheme
1 mark
500² + 350² (= 250 000 + 122 500); or a correct final answer of 610.3 mm with no working
An answer of 610.3 mm (accept 610 to 610.4) with no working scores 3 marks.
1 mark
= 372 500 / √372 500
Allow ECF for an arithmetic slip in the squares.
1 mark
610.3 mm
Accept 610, 610.3 or 610.33 mm. Allow ECF: the square root of their sum. Common errors: 372 500 with no square root scores 2 marks; 500 + 350 = 850 mm scores 0.
Question 4
6 marks
An M8 internal thread is to be cut by hand in a hole that goes right through a 12 mm thick steel plate.
Describe, in stages, how the thread would be cut. Include the tools and equipment used and any safety precautions.
Model answer
1. Coat the plate with engineer's blue, mark the hole centre with a scriber, steel rule and engineer's square, and centre punch it. 2. Clamp the plate in a machine vice on the pillar drill and, wearing goggles with the guard down, drill a 6.8 mm tapping size hole through the plate. 3. Lightly countersink the top of the hole to remove the burr and help the tap to start. 4. Hold the plate level in a bench vice. 5. Fit the taper (first) tap into a tap wrench, put it in the hole and check it is upright with an engineer's square. 6. Put a little cutting compound on the tap. 7. Turn the tap wrench clockwise half a turn, then back a quarter of a turn to break the swarf, and keep repeating this until the tap has gone through the plate, checking it stays square. 8. Run the second tap and then the plug tap through to make sure the thread is full depth. 9. Never force the tap if it becomes tight, as it is brittle and can snap off in the hole. 10. Brush out the swarf (not with fingers) and check the thread by screwing in an M8 bolt.
Explanation
Top answers give the full sequence: marking out, drilling the correct tapping size, starting the taper tap square in a tap wrench, using cutting compound, the half-turn forward and quarter-turn back technique, finishing with the second and plug taps, and checking the thread, with safety throughout (goggles and guard when drilling, not forcing the brittle tap, brushing swarf). Lists of stages with no detail are limited to 2 marks.
Mark scheme
6 marks
Levels of response (6 marks). Level 3 (5-6 marks): Detailed explanation including all key stages to cut the internal thread, with the equipment/tools used and safety. Notes are clear and in a logical order. Level 2 (3-4 marks): Some stages described in detail OR the majority of stages covered but with insufficient detail to allow the thread to be cut correctly. Level 1 (1-2 marks): One or more basic steps/stages listed. 0 marks: No response or nothing worthy of credit.
Max 2 if the stages are only listed with no detail. Indicative content, key stages in order (accept all other valid responses): 1. Mark out the hole position with a scriber, steel rule and engineer's square on engineer's blue, and centre punch it. 2. Clamp the plate in a machine vice and drill the tapping size hole (6.8 mm for M8) on a pillar drill, with the guard down and goggles worn. 3. Lightly countersink or deburr the hole so the tap starts easily. 4. Hold the plate level in a bench vice. 5. Fit the taper (first) tap in a tap wrench and start it square to the surface, checking with an engineer's square. 6. Apply cutting compound or oil. 7. Turn the tap clockwise about half to one turn, then back about a quarter turn to break off the swarf; repeat until the tap is through the plate. 8. Follow with the second (intermediate) and then the plug tap to cut a full thread. 9. Do not force the tap: taps are hard and brittle and can snap. 10. Clean the swarf out with a brush and check the thread with an M8 bolt or thread gauge.
Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.
Ctrl + Enter to check
Study HelperHints first, answers after you try
Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.