Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
Avg
score:
–
Topics
done:
0/30

Temperature changes in a system and specific heat capacity

Practise 12 exam-style questions on Temperature changes in a system and specific heat capacity for AQA GCSE Combined Science (Physics Paper 1). Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 12 questions
  • 1–6 marks each
  • Instant marking
  • No sign-up needed
12 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

2 marks

Define the specific heat capacity of a substance.

Model answer

The specific heat capacity of a substance is the amount of energy required to raise the temperature of one kilogram of the substance by one degree Celsius.

Explanation

Specific heat capacity tells you how much energy a material needs to warm up: it is measured per kilogram and per degree. Water has a very high specific heat capacity (about 4200 J/kg °C), so it takes a lot of energy to heat up.

Mark scheme
  1. 1 mark

    the amount of energy required to raise the temperature of 1 kg of the substance

    allow energy needed to heat one kilogram

  2. 1 mark

    by 1 °C

    allow by one degree Celsius; allow by 1 K

Question 2

3 marks

A 500 g block of aluminium is heated from 20 °C to 80 °C.
The specific heat capacity of aluminium is 900 J/kg °C.

The equation linking change in thermal energy, mass, specific heat capacity and temperature change is:
change in thermal energy = mass × specific heat capacity × temperature change

Calculate the energy needed to heat the block.

Model answer

mass = 500 g = 0.500 kg
temperature change = 80 − 20 = 60 °C
ΔE = m × c × Δθ
ΔE = 0.500 × 900 × 60
ΔE = 27 000 J

Explanation

Two steps catch students out: converting grams to kilograms (÷ 1000) and using the change in temperature (80 − 20 = 60 °C) rather than the final temperature. Using 500 instead of 0.500 gives an answer 1000 times too big.

Mark scheme
  1. 1 mark

    mass = 0.5(00) kg and temperature change = 60 (°C)

    both needed; an answer of 27 000 J scores 3 marks

  2. 1 mark

    ΔE = 0.500 × 900 × 60

    allow ecf from an incorrect mass or temperature change

  3. 1 mark

    27 000 (J)

    allow 27 kJ if unit given; allow ecf

Question 3

3 marks

A student did an experiment to find the specific heat capacity of aluminium. She calculated a value of 1050 J/kg °C. The accepted value is 900 J/kg °C.

Explain why her value is higher than the accepted value, and suggest one way she could improve her experiment.

Model answer

Some of the energy supplied by the heater was transferred to the surroundings instead of heating the aluminium. So the temperature rise was smaller than it would have been if all the energy had heated the block. Because c = ΔE ÷ (m × Δθ), using the total energy supplied with a smaller temperature rise gives a value that is too large. She could improve the experiment by wrapping the block in insulation to reduce the energy transferred to the surroundings.

Explanation

In this type of experiment the energy supplied is measured accurately, but not all of it ends up in the block. A smaller temperature rise for the same energy makes the calculated specific heat capacity too high. Insulation reduces energy transfer to the surroundings; repeating does not fix a systematic error like this.

Mark scheme
  1. 1 mark

    some of the energy supplied was transferred to the surroundings / did not heat the aluminium

    allow energy was wasted heating the air / the bench / the heater

  2. 1 mark

    so the temperature rise was smaller than it should be, and c = ΔE ÷ (m × Δθ) came out too large

    allow so the energy used in the calculation was more than the energy that heated the block

  3. 1 mark

    insulate the block / wrap the block in insulation

    allow put a lid / insulating mat under the block; allow add oil / water to the thermometer hole for better thermal contact; ignore repeat

Question 4

4 marks

A hot water tank contains 150 kg of water. A 3.0 kW immersion heater heats the water from 15 °C to 55 °C.
The specific heat capacity of water is 4200 J/kg °C.

The equation linking change in thermal energy, mass, specific heat capacity and temperature change is:
change in thermal energy = mass × specific heat capacity × temperature change

Calculate the time taken to heat the water, in minutes.
Assume all the energy from the heater is transferred to the water.

Model answer

temperature change = 55 − 15 = 40 °C
ΔE = m × c × Δθ = 150 × 4200 × 40 = 25 200 000 J
power = energy ÷ time, so time = energy ÷ power
t = 25 200 000 ÷ 3000 = 8400 s
t = 8400 ÷ 60 = 140 minutes

Explanation

This links two ideas: ΔE = m c Δθ gives the energy the water needs, and P = E ÷ t gives the time the heater takes to supply it. Convert 3.0 kW to 3000 W and the seconds to minutes. In reality some energy is transferred to the surroundings, so it would take longer.

Mark scheme
  1. 1 mark

    ΔE = 150 × 4200 × 40

    an answer of 140 minutes scores 4 marks

  2. 1 mark

    ΔE = 25 200 000 (J)

    allow 2.52 × 10⁷ J

  3. 1 mark

    t = 25 200 000 ÷ 3000 = 8400 (s)

    allow ecf from an incorrect energy; power must be in W

  4. 1 mark

    140 (minutes)

    allow ecf from their time in seconds ÷ 60

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Revision notes

Temperature changes in a system and specific heat capacity

The big idea

Give the same energy to a kilogram of water and a kilogram of olive oil, and the temperature of the oil rises about twice as much. When a system is heated without changing state, its temperature rise depends on three things: the energy input, the mass of the substance and the type of material. The effect of the material is measured by its specific heat capacity.

The equation

\[\text{change in thermal energy} = \text{mass} \times \text{specific heat capacity} \times \text{temperature change}\]
\[\Delta E = m\,c\,\Delta\theta\]
  • change in thermal energy, \(\Delta E\), in joules, J
  • mass, \(m\), in kilograms, kg
  • specific heat capacity, \(c\), in joules per kilogram per degree Celsius, J/kg °C
  • temperature change, \(\Delta\theta\) (theta), in degrees Celsius, °C

This equation is given on the Physics equation sheet: you must choose it and use it, but you do not have to recall it. Rearranged, \(c = \dfrac{\Delta E}{m\,\Delta\theta}\), \(m = \dfrac{\Delta E}{c\,\Delta\theta}\) and \(\Delta\theta = \dfrac{\Delta E}{m\,c}\).

\(\Delta\theta\) is a change: the final temperature minus the starting temperature. For something that is cooling, \(\Delta E\) is the energy it transfers to its surroundings.

Specific heat capacity

The specific heat capacity of a substance is the amount of energy required to raise the temperature of one kilogram of the substance by one degree Celsius.

SubstanceSpecific heat capacity in J/kg °C
Water4200
Ice2100
Olive oilabout 2000
Aluminium900
Copper385

A substance with a high specific heat capacity needs a lot of energy for each kilogram and each degree, so it warms up slowly, and it releases a lot of energy as it cools. Water's very high value makes it good for storing energy and carrying it around a building, as in hot water bottles and central heating. Metals have low values, so a metal pan heats up quickly. For the same mass and the same energy input, the material with the lower specific heat capacity has the bigger temperature rise.

Temperatures below zero

A 1.5 kg block of ice is taken from a freezer at −22 °C and warms to −4 °C. It does not melt. The specific heat capacity of ice is 2100 J/kg °C. Calculate the energy transferred to the ice, in kJ.

\(\Delta\theta = -4 - (-22) = 18\) °C

\(\Delta E = m\,c\,\Delta\theta = 1.5 \times 2100 \times 18 = 56\,700\) J

\(56\,700 \div 1000 = 56.7\) kJ, which is 57 kJ to 2 significant figures

Finding a final temperature after cooling

A 0.60 kg steel horseshoe is taken from a forge at 420 °C and left to cool. In the next 10 minutes it transfers 81 kJ of energy to its surroundings. The specific heat capacity of steel is 450 J/kg °C. Calculate its temperature at the end of the 10 minutes.

Convert the energy: 81 kJ = 81 000 J

\(\Delta\theta = \dfrac{\Delta E}{m\,c} = \dfrac{81\,000}{0.60 \times 450} = \dfrac{81\,000}{270} = 300\) °C

The horseshoe is cooling, so subtract: final temperature \(= 420 - 300 = 120\) °C

Measuring specific heat capacity

Specific heat capacity is measured in a required practical (see also: Energy changes in systems, where the method, variables, safety and errors are set out). A metal block of known mass is heated by an immersion heater. A joulemeter measures the energy supplied (or use an ammeter, a voltmeter and a stopclock, with \(P = VI\) and \(E = Pt\), which you must recall), and a thermometer measures the temperature rise. Then \(c = \dfrac{\Delta E}{m\,\Delta\theta}\).

Diagram of the apparatus for measuring the specific heat capacity of a metal block. A metal block with two holes stands in a layer of insulation; an immersion heater is in one hole and a thermometer in the other. The heater is connected to a power supply through a box with a display marked J. Labelled parts: Thermometer, Metal block, Immersion heater, Insulation, Power supply, Joulemeter.
The joulemeter measures the energy supplied to the heater; the thermometer measures the rise in temperature of the block.

Common mistakes

  • Using the final temperature (or the starting one) as \(\Delta\theta\). Subtract to find the change.
  • Leaving the mass in grams. Specific heat capacity is per kilogram, so a mass in grams gives an energy 1000 times too big.
  • Leaving the energy in kJ when \(c\) is in J/kg °C. Convert kJ to J first.
  • Giving the unit as J/kg or J/°C. It is J/kg °C.
  • Leaving "one kilogram" or "one degree Celsius" out of the definition. Both are needed for the marks.

Exam tip

Write the equation from the sheet, substitute the values with their units converted, then rearrange. In a "show that" question, write the unrounded value from your calculator (at least 3 significant figures), so the examiner can see that you calculated it and did not just copy the value you were given.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.