Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
Avg
score:
–
Topics
done:
0/30

Power

Practise 11 exam-style questions on Power for AQA GCSE Combined Science (Physics Paper 1). Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 11 questions
  • 1–4 marks each
  • Instant marking
  • No sign-up needed
11 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

Write down the equation that links power (P), current (I) and resistance (R).

Model answer

power = (current)² × resistance
P = I² R

Explanation

This equation is useful when you know the current and resistance but not the potential difference. The current is squared, so the power depends strongly on the current.

Mark scheme
  1. 1 mark

    power = current² × resistance

    allow P = I² R; allow P = I × I × R; do not accept P = I R

Question 2

3 marks

There is a current of 200 mA in a resistor of resistance 150 Ω.

Calculate the power transferred in the resistor.

Model answer

I = 200 mA = 0.200 A
P = I² R
P = 0.200² × 150
P = 0.040 × 150 = 6.0 W

Explanation

Convert milliamps to amperes first (divide by 1000), then square the current before multiplying by the resistance. Forgetting to square the current is a common mistake.

Mark scheme
  1. 1 mark

    I = 0.200 A

    conversion of mA to A; an answer of 6.0 (W) scores 3 marks

  2. 1 mark

    P = 0.200² × 150

    allow ecf from an incorrect conversion

  3. 1 mark

    6.0 (W)

    allow 6 (W); allow ecf; an answer of 30 (W) (current not squared) scores 1 mark

Question 3

3 marks

A heater has a power of 1150 W when the current in it is 5.0 A.

Calculate the resistance of the heater.

Model answer

P = I² R
1150 = 5.0² × R
R = 1150 ÷ 25
R = 46 Ω

Explanation

Rearrange P = I² R to give R = P ÷ I². Square the current first. You could also find the potential difference (P ÷ I = 230 V) and then use R = V ÷ I; both methods give 46 Ω.

Mark scheme
  1. 1 mark

    1150 = 5.0² × R

    an answer of 46 (Ω) scores 3 marks

  2. 1 mark

    R = 1150 ÷ 25

  3. 1 mark

    R = 46 (Ω)

    allow ecf; an answer of 230 (Ω) (current not squared) scores 1 mark

Question 4

4 marks

Kettle A has a power of 3.0 kW and kettle B has a power of 2.0 kW. Each kettle is used to boil the same mass of water from the same starting temperature. Kettle A takes 120 s. Assume all the energy transferred by each kettle heats the water.

Explain which kettle boils the water faster, and calculate the time kettle B takes.

Model answer

Kettle A boils the water faster. Both kettles must transfer the same amount of energy to the water, but kettle A has the greater power, so it transfers energy at a greater rate.
Energy needed = power × time = 3000 × 120 = 360 000 J
Time for kettle B = energy ÷ power = 360 000 ÷ 2000 = 180 s

Explanation

Power is the rate of energy transfer, so for the same energy the time taken is inversely proportional to the power. Kettle B has two thirds of the power of kettle A, so it takes one and a half times as long.

Mark scheme
  1. 1 mark

    kettle A boils the water faster because it has a greater power, so it transfers energy at a greater rate

  2. 1 mark

    both kettles must transfer the same amount of energy to the water

  3. 1 mark

    energy = 3000 × 120 = 360 000 (J)

    an answer of 180 (s) scores the last 2 marks

  4. 1 mark

    time for B = 360 000 ÷ 2000 = 180 (s)

    allow ecf from their energy; allow 120 × 3.0 ÷ 2.0 = 180 (s)

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Revision notes

Power

The big idea

The power of a circuit device is the rate at which it transfers energy: the energy it transfers each second. It depends on the potential difference across the device and the current through it. Two equations let you calculate it, and the second one explains why a large current heats cables so much.

Power, potential difference and current

\[\text{power} = \text{potential difference} \times \text{current} \qquad P = VI\]
\[\text{power} = (\text{current})^2 \times \text{resistance} \qquad P = I^2 R\]
  • power, \(P\), in watts, W
  • potential difference, \(V\), in volts, V
  • current, \(I\), in amperes, A (amp is also fine)
  • resistance, \(R\), in ohms, Ω

You must recall both equations. A power of 1 W means 1 joule of energy is transferred every second, and 1 kW = 1000 W.

Why \(P = VI\) works: the potential difference is the energy transferred by each coulomb of charge (joules per coulomb), and the current is the number of coulombs each second. Multiplying them gives the joules transferred each second, which is the power. So a bigger potential difference or a bigger current means energy is transferred at a greater rate, and over a longer time more energy is transferred in total (see also: Energy transfers in everyday appliances).

Which equation?

  • You know \(V\) and \(I\): use \(P = VI\).
  • You know \(I\) and \(R\): use \(P = I^2 R\). Square the current first; only the current is squared.
  • You know \(V\) and \(R\): find the current with \(I = \dfrac{V}{R}\), then use either equation.

Is the extension lead overloaded?

A 3.0 kW kettle and a 2.0 kW toaster are both switched on, plugged into one extension lead on the 230 V mains. The lead is designed to carry a current of up to 13 A. Is it overloaded?

The appliances are in parallel, so their powers add: \(P = 3000 + 2000 = 5000\) W

\(P = VI\), so \(I = \dfrac{P}{V} = \dfrac{5000}{230} = 21.7\ldots\)

\(I = 22\) A (2 significant figures). This is far more than 13 A, so the lead is overloaded: its fuse should melt before the cable overheats.

The heating effect of a current

\(P = I^2 R\) shows that, for a fixed resistance, the power transferred by heating is proportional to the square of the current. Doubling the current makes the power four times as large, not twice as large. This is why cables for high-power appliances are thick (a low resistance), and why the National Grid sends electricity with a small current.

A hot-wire foam cutter

The wire in a foam cutter has a resistance of 2.5 Ω and the current in it is 1.6 A. Calculate the power of the wire with \(P = I^2 R\), then check it with \(P = VI\).

\(P = I^2 R = 1.6^2 \times 2.5 = 2.56 \times 2.5 = 6.4\) W

Check: the p.d. across the wire is \(V = IR = 1.6 \times 2.5 = 4.0\) V, so \(P = VI = 4.0 \times 1.6 = 6.4\) W

Both equations give the same power: \(P = I^2 R\) is \(P = VI\) with \(IR\) written in place of \(V\).

Power in series and parallel

  • In series the current is the same in each resistor, so from \(P = I^2 R\) the larger resistance transfers energy at the greater rate.
  • In parallel the potential difference is the same across each resistor, so the smaller resistance takes the larger current and, from \(P = VI\), has the greater power. Mains appliances are all at about 230 V, so a higher-power appliance always takes a larger current.

Remember

  • Power is the rate of energy transfer: 1 W = 1 J/s.
  • \(P = VI\) and \(P = I^2 R\) must both be recalled.
  • Only the current is squared in \(P = I^2 R\); doubling the current quadruples the power.
  • Convert kW to W and mA to A before you substitute.

Common mistakes

  • Writing \(P = IR\). That gives a potential difference, not a power.
  • Forgetting to square the current, or squaring the resistance as well.
  • When \(I\) is the unknown in \(P = I^2 R\), stopping at \(I^2\). Take the square root.
  • Saying doubling the current doubles the heating effect. It quadruples it.
  • Using the supply's potential difference for one component in a series circuit. Use the p.d. across that component.

Exam tip

In calculations, write the equation you are using before substituting, so a slip in the arithmetic can still earn the method marks. When a question asks which of two devices has the greater power, work out both powers, then name the device: the numbers alone do not answer the question.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.