Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
Edexcel GCSE Physics (Paper 2) Smart practice A mixed round aimed at your weak spots
Unit 1
Key concepts of physics
Unit 8
Energy - forces doing work
Unit 9
Forces and their effects
Unit 10
Electricity and circuits
Unit 11
Static electricity
Unit 12
Magnetism and the motor effect
Unit 13
Electromagnetic induction
Unit 14
Particle model
Unit 15
Forces and matter
Avg
score:
–
Topics
done:
0/34

Core practical: specific heat capacity and melting ice

Practise 14 exam-style questions on Core practical: specific heat capacity and melting ice for Edexcel GCSE Physics (Paper 2). Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 14 questions
  • 1–6 marks each
  • Instant marking
  • No sign-up needed
14 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

In a core practical, water is heated with an immersion heater to find its specific heat capacity. The temperature of the water is measured with a thermometer.

Give a reason why the bulb of the thermometer must not touch the immersion heater.

Model answer

The heater is much hotter than the water, so a thermometer touching it would show the temperature of the heater, which is higher than the temperature of the water.

Explanation

The calculation needs the temperature rise of the water. The surface of the immersion heater is much hotter than the water around it, so a thermometer touching it reads too high, giving a temperature rise that is too large and a value of c that is too small.

Mark scheme
  1. 1 mark

    the thermometer would measure the temperature of the (hotter) heater, not the water / the reading would be higher than the temperature of the water (1)

    Accept 'the reading would be too high, so the temperature rise would be too large'. Ignore 'the thermometer might break' on its own. Ignore 'it would be inaccurate' with no reason.

Question 2

2 marks

Max puts crushed ice and a thermometer into a boiling tube, and stands the tube in a beaker of warm water (a water bath). He records the temperature every minute to obtain a temperature-time graph. His results show the temperature staying constant at 2 °C while the ice melts.

Pure ice melts at 0 °C.

Suggest two reasons why Max's results show a constant temperature of 2 °C.

Model answer

The thermometer may have a zero error, so it reads 2 °C too high at every temperature. Alternatively, the thermometer bulb may not have been surrounded by ice: if it was in melted water, or touching the side of the boiling tube warmed by the water bath, it would read a temperature above 0 °C.

Explanation

A constant temperature during melting shows the ice is melting, so a constant value that is not 0 °C points to a problem with the measurement. A systematic error such as a zero error shifts every reading by the same amount; poor contact with the ice means the thermometer measures something warmer. Impurities would lower, not raise, the melting point.

Mark scheme
  1. 1 mark

    the thermometer has a zero error / is not calibrated correctly / reads 2 °C too high (1)

    Any two from the three points; max 2. Accept 'a systematic error in the thermometer'.

  2. 1 mark

    the thermometer bulb was not surrounded by ice / was in melted water that was warmer than 0 °C (because the mixture was not stirred) (1)

    Accept 'the thermometer was measuring the water, not the ice'.

  3. 1 mark

    the thermometer bulb was touching the side of the boiling tube, which was warmed by the water bath (1)

    Accept 'the thermometer touched the glass, which was hotter than the ice'. Do not accept 'impurities in the ice' (dissolved impurities such as salt lower the melting point). Ignore 'human error' with no explanation.

Question 3

3 marks

Sam heats 0.050 kg of crushed ice in a boiling tube that stands in a water bath. The temperature of the ice reaches 0 °C after 1.5 minutes. The temperature then stays at 0 °C until all of the ice has melted, 9.5 minutes after the start.

The specific latent heat of fusion of ice is 334 000 J/kg.

Calculate the average rate at which energy was transferred to the ice while it melted. Give your answer in watts.

Use the equation
Q = m × L

Model answer

Energy to melt the ice: Q = m × L = 0.050 × 334 000 = 16 700 J
Time taken to melt: 9.5 - 1.5 = 8.0 minutes = 480 s
Average rate of energy transfer = energy ÷ time = 16 700 ÷ 480 = 35 W

Explanation

While the ice melts, all the energy transferred from the water bath is used to change its state, so the energy is m × L. The melting time is only the time the temperature stays at 0 °C (the flat part of a temperature-time graph), from 1.5 to 9.5 minutes, and it must be in seconds to give a power in watts (J/s). A common error is to divide by the whole time from the start.

Mark scheme
  1. 1 mark

    (Q =) 0.050 × 334 000 = 16 700 (J) (1)

    An answer of 35 (W) with no working scores 3 marks.

  2. 1 mark

    (time to melt =) 9.5 - 1.5 = 8.0 minutes / 480 s (1)

    Using 9.5 minutes (570 s), the whole time from the start, is a wrong method and does not score this mark: 16 700 ÷ 570 = 29 W scores MP1 only.

  3. 1 mark

    (rate =) 16 700 ÷ 480 = 35 (W) (1)

    Accept 34.8 W or 35 J/s. Allow ecf from the student's energy and time. The time left in minutes (16 700 ÷ 8.0 = 2090, given as J/min, W or with no unit) is a unit-conversion error that loses this mark only: it scores MP1 and MP2.

Question 4

5 marks

Ruth determines the specific heat capacity of water. She heats 300 g of water in a beaker with an immersion heater connected to a joulemeter.
- temperature of the water at the start = 19.5 °C
- highest temperature of the water = 31.0 °C
- joulemeter reading at the start = 0 J
- joulemeter reading at the end = 15 900 J

Calculate the specific heat capacity of water from Ruth's results.

Use the equation
ΔQ = m × c × Δθ

Ruth's value is higher than the accepted value of 4200 J/kg °C.

Suggest one change to her apparatus that would give a value closer to 4200 J/kg °C.

Model answer

Δθ = 31.0 - 19.5 = 11.5 °C
m = 300 g = 0.300 kg
c = ΔQ ÷ (m × Δθ) = 15 900 ÷ (0.300 × 11.5) = 4609 J/kg °C (about 4600 J/kg °C)
Ruth could wrap the beaker in an insulating material such as cotton wool and put a lid on it. This reduces the energy transferred from the water and the beaker to the surroundings, so more of the 15 900 J measured by the joulemeter heats the water and her value is closer to 4200 J/kg °C.

Explanation

Find the temperature rise and convert the mass into kilograms before substituting into the rearranged equation. The joulemeter measures all the energy supplied to the heater, but some of it is transferred to the beaker and the surroundings rather than the water, so the calculated value is too high. Insulating the beaker and using a lid reduce this systematic error; repeating the experiment does not.

Mark scheme
  1. 1 mark

    (Δθ =) 31.0 - 19.5 = 11.5 (°C) (1)

    An answer of 4600 J/kg °C (or a value that rounds to it, e.g. 4609 J/kg °C) with no working scores marking points 1, 2, 3 and 4.

  2. 1 mark

    rearrangement: c = ΔQ ÷ (m × Δθ) (1)

    Accept the rearrangement with values substituted.

  3. 1 mark

    substitution: (c =) 15 900 ÷ (0.300 × 11.5) (1)

    Allow ecf from the student's Δθ. Using 31.0 °C (the final temperature) as Δθ is a wrong method: 15 900 ÷ (0.300 × 31.0) = 1710 scores MP2 only.

  4. 1 mark

    evaluation: 4600 (J/kg °C) (1)

    Accept values that round to 4600, e.g. 4609. Using 300 g not converted into kg (e.g. 4.6) is a unit-conversion error that loses this mark only: it scores 3 marks.

  5. 1 mark

    insulate the beaker / wrap the beaker in an insulating material (e.g. cotton wool, foam, bubble wrap) / put a lid on the beaker / use a polystyrene cup instead of a glass beaker (1)

    Accept 'use an insulated container' or any other change that reduces the energy transferred to the beaker or the surroundings, e.g. 'stand the beaker on an insulating mat'. Ignore 'repeat the experiment and take a mean' (repeating does not reduce this systematic error). Ignore 'use a more accurate thermometer / joulemeter' with no reason.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.