Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
Edexcel GCSE Physics (Paper 2) Smart practice A mixed round aimed at your weak spots
Unit 1
Key concepts of physics
Unit 8
Energy - forces doing work
Unit 9
Forces and their effects
Unit 10
Electricity and circuits
Unit 11
Static electricity
Unit 12
Magnetism and the motor effect
Unit 13
Electromagnetic induction
Unit 14
Particle model
Unit 15
Forces and matter
Avg
score:
–
Topics
done:
0/34

Atmospheric pressure and pressure in fluids

Practise 15 exam-style questions on Atmospheric pressure and pressure in fluids for Edexcel GCSE Physics (Paper 2). Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 15 questions
  • 1–6 marks each
  • Instant marking
  • No sign-up needed
15 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

A crate rests on the floor on its smallest face. A second, identical crate is stacked on top of it. The bottom crate is then turned onto a larger face, which has three times the area of the smallest face, with the second crate still on top of it.

How does the pressure on the floor now compare with the pressure when the single crate rested on its smallest face?

Choose your answer.

  • A two-thirds as large
  • B 1.5 times as large
  • C the same
  • D 6 times as large

Model answer

A - two-thirds as large. The force is twice as large and the area is three times as large, so the pressure is 2 ÷ 3 of the original.

Explanation

Pressure is directly proportional to the force and inversely proportional to the area. Doubling the force doubles the pressure, and tripling the area divides it by three, so the overall factor is 2 ÷ 3. Students who think a larger area gives a larger pressure choose D.

Mark scheme
  1. 1 mark

    A / two-thirds as large (1)

    The only correct answer is A: pressure = force ÷ area; the force on the floor is doubled (the weight of two crates) and the area is three times as large, so the pressure is 2 ÷ 3 = two-thirds of the original pressure. B is not correct because 1.5 = 3 ÷ 2 inverts the ratio (it divides the area factor by the force factor); C is not correct because the force and the area change by different factors; D is not correct because 6 = 2 × 3 multiplies by the area factor, but a larger area gives a smaller pressure. Accept the letter or the option. If more than one option is given, do not award the mark.

Question 2

2 marks

A teacher fills a hollow glass sphere with water. The sphere has small holes all over its surface and is joined to a wide tube with a plunger.

When the teacher pushes the plunger in, water squirts out of every hole, including the holes on the top, the sides and the bottom of the sphere. Each jet of water leaves the sphere at right angles to its surface.

Explain why each jet leaves at right angles to the surface of the sphere.

Model answer

Pressure in a fluid acts in all directions, so pushing the plunger increases the pressure everywhere in the water, at every hole. The pressure of the water produces a force that is normal (at right angles) to the surface of the sphere at each point, so at each hole the water is pushed outwards at right angles to the surface.

Explanation

The pressure in a fluid causes a force at right angles to any surface it touches, whichever way the surface faces. That is why the jets point straight out from the sphere in every direction, not just in the direction in which the plunger moves. A common mistake is to think that the push of the plunger only moves the water forwards.

Mark scheme
  1. 1 mark

    the pressure in the water acts in all directions / at every point on the inside of the sphere (1)

    An explanation linking. accept the pressure is increased everywhere in the water (so water is pushed out of holes facing in every direction); ignore 'the water is under pressure' alone.

  2. 1 mark

    the pressure (of the water) causes a force normal / at right angles / perpendicular to the surface (at each hole), so the water is pushed out at right angles to the surface (1)

    accept 'normal' or 'perpendicular'; do not accept 'the force acts in the direction the plunger pushes' or 'the force acts downwards'.

Question 3

3 marks

A mobile crane stands on four outriggers. Each outrigger rests on a flat pad on the ground.

When the crane lifts a heavy load, one outrigger pushes down on its pad with a force of 120 kN. The ground under the pad can safely withstand a pressure of up to 200 kPa.

Calculate the smallest area of pad that should be used under this outrigger. Ignore the weight of the pad.

Model answer

pressure = force ÷ area, so area = force ÷ pressure
area = 120 000 N ÷ 200 000 Pa
area = 0.60 m²

Explanation

Rearranging P = F ÷ A gives A = F ÷ P. A large pad spreads the force over a large area, so the pressure on the ground stays within the safe limit. Because 1 Pa = 1 N/m², newtons divided by pascals gives square metres; kN divided by kPa also works because the prefixes cancel. A common error is to divide the pressure by the force.

Mark scheme
  1. 1 mark

    rearrangement: (area =) force ÷ pressure (1)

    An answer of 0.60 m² with no working scores 3 marks (accept 0.6 m² or 6000 cm²). P = F ÷ A is not given in the question: it must be recalled. An answer of 1.67 (pressure ÷ force, a wrong rearrangement) scores 0. An answer whose only error is a power of ten from converting only one of kN and kPa (e.g. 0.00060 m² or 600 m²) scores 2 marks.

  2. 1 mark

    substitution: (area =) 120 000 ÷ 200 000 / 120 ÷ 200 (1)

    accept kN ÷ kPa used consistently (the prefixes cancel).

  3. 1 mark

    evaluation: 0.60 (m²) (1)

    allow 0.6 (m²); accept 6000 cm².

Question 4

4 marks

Zara wants to estimate atmospheric pressure. She has:
- a plastic syringe with a scale from 0 to 20 cm³ and a cap that seals its nozzle
- a newtonmeter that reads up to 50 N
- a clamp stand
- a 30 cm ruler.

If the plunger is pushed fully in and the nozzle is then sealed, there is almost no air inside the syringe, so pulling the plunger out needs a force about equal to the force of the atmosphere on the plunger.

Describe how Zara could use this equipment to estimate atmospheric pressure. Your answer should include the measurements she makes and how she uses them to calculate the pressure.

Model answer

Zara pushes the plunger fully in to remove the air, fits the cap to seal the nozzle and clamps the barrel to the clamp stand. She hooks the newtonmeter onto the plunger and pulls it steadily, reading the force at the moment the plunger starts to move. Because there is almost no air inside, this force is about equal to the force of the atmosphere on the plunger.

She measures the length of the scale from 0 to 20 cm³ with the ruler, for example 6.4 cm, and calculates the area of the plunger: area = volume ÷ length = 20 ÷ 6.4 = 3.1 cm². She converts this to m² by dividing by 10 000: 3.1 × 10⁻⁴ m². (A force of about 31 N would then give a pressure of about 100 000 Pa.)

She calculates atmospheric pressure = force ÷ area, with the force in N and the area in m², to give the pressure in Pa. She repeats the measurement a few times and calculates a mean. Friction between the plunger and the barrel makes the force too large, so she can measure the force needed to move the plunger with the cap removed and subtract it.

Explanation

With almost no air inside the sealed syringe, the atmosphere pushes the plunger in with a force equal to atmospheric pressure × the area of the plunger, because the pressure acts at right angles to the plunger. Measuring the force needed to just move the plunger and the area (volume ÷ length of the scale) gives P = F ÷ A, which needs the area in m² to give pascals. Friction makes the estimate too large, and air leaking in past the plunger makes it too small.

Mark scheme
  1. 1 mark

    clamp the barrel of the syringe (after pushing the plunger fully in and sealing the nozzle), so that the syringe cannot move when the plunger is pulled (1)

    A description including any four of the six points; max 4. Max 3 if the answer does not explain how the area of the plunger is found. Accept 'hold the barrel still' for 'clamp the barrel'. Pushing the plunger in and sealing the nozzle repeat the question and do not score on their own.

  2. 1 mark

    pull the plunger with the newtonmeter and read the force when the plunger just starts to move (1)

    Accept 'pull steadily and read the newtonmeter as the plunger moves out slowly'.

  3. 1 mark

    measure the length of the scale from 0 to 20 cm³ with the ruler, and calculate the area of the plunger = volume ÷ length (e.g. 20 cm³ ÷ 6.4 cm = 3.1 cm²) (1)

    Accept 'measure the diameter of the plunger with the ruler and calculate the area (π × radius²)'. The area must be calculated from a measurement, not just 'measure the area'.

  4. 1 mark

    convert the area to m² (divide the area in cm² by 10 000) (1)

    Accept 1 cm² = 1 × 10⁻⁴ m². Accept working out the pressure in N/cm² and multiplying by 10 000 to give Pa.

  5. 1 mark

    atmospheric pressure = force ÷ area / P = F ÷ A (gives the pressure in Pa) (1)

    P = F ÷ A must be recalled. Do not accept 'pressure = force × area'.

  6. 1 mark

    repeat the measurement and calculate a mean / allow for friction, e.g. by measuring the force needed to move the plunger with the cap removed and subtracting it (1)

    Accept 'friction makes the force, and so the estimate, too large'. Ignore 'repeat for accuracy' with no mean.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.