Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
OCR GCSE Chemistry (Paper 2) Smart practice A mixed round aimed at your weak spots
Unit 4
Predicting and identifying reactions and products
Unit 5
Monitoring and controlling chemical reactions
Unit 6
Global challenges
Unit 7
Practical skills
Avg
score:
–
Topics
done:
0/34

The technique of titration

Practise 10 exam-style questions on The technique of titration for OCR GCSE Chemistry (Paper 2). Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 10 questions
  • 1–3 marks each
  • Instant marking
  • No sign-up needed
10 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

A student titrates potassium hydroxide solution with dilute sulfuric acid. In her rough titration she runs the acid in quickly, swirling the flask, until the indicator changes colour. Her rough titre is 24.70 cm³.

She refills the burette to 0.00 cm³ for her first accurate titration.

How should she add the acid in this titration?

Choose your answer.

  • A Add 24.70 cm³ of acid quickly, then add a few more drops to be sure the colour has changed.
  • B Add 24.70 cm³ of acid quickly, then stop and record 24.70 cm³ as her titre.
  • C Add the acid as quickly as in the rough titration, until the indicator changes colour.
  • D Add the acid quickly to about 23.5 cm³, then drop by drop until the colour changes.

Model answer

D - Add the acid quickly to about 23.5 cm³, then drop by drop until the colour changes.

Explanation

A rough titration is done quickly, so it usually goes a little past the end point, but it shows roughly how much acid is needed. In the accurate titrations the acid can be run in quickly to about 1 cm³ less than the rough titre and then added drop by drop, swirling the flask, so that she stops as soon as one drop makes the indicator change colour. The rough titre is not used when the mean titre is calculated.

Mark scheme
  1. 1 mark

    D / Add the acid quickly to about 23.5 cm³, then drop by drop until the colour changes.

    The only correct answer is D: the rough titre shows roughly how much acid is needed, but it is usually a little too large because the acid was run in quickly; so she runs the acid in quickly to about 1 cm³ less than the rough titre and then adds it drop by drop, swirling, so that she can stop as soon as one drop makes the indicator change colour. A is not correct because adding more drops after the colour has changed takes her past the end point, so her titre would be too large. B is not correct because the rough titre is only approximate (the end point was probably overshot), and the titre must be found from the colour change of the indicator, not copied from the rough titre. C is not correct because running the acid in quickly all the way to the colour change is likely to overshoot the end point again, as in the rough titration. ALLOW the letter or the option. If more than one option is given, do not award the mark.

Question 2

1 mark

In a titration, the alkali and the indicator are put in a conical flask, not in a beaker. The acid is added from a burette, and the flask is swirled after each addition.

Suggest why a conical flask is used rather than a beaker.

Model answer

The conical flask narrows towards the top, so it can be swirled to mix the acid and alkali without any of the solution splashing or spilling out.

Explanation

The flask must be swirled after each addition so that the acid mixes with all of the alkali. A beaker has straight sides and a wide top, so swirling it could make the solution splash out, and any solution lost would change the volume of acid needed. The conical flask does not measure the volume: the pipette measures the alkali and the burette measures the acid.

Mark scheme
  1. 1 mark

    the flask can be swirled (to mix the solutions) without any liquid splashing or spilling out (because it is narrower at the top)

    ALLOW the narrow neck / sloping sides stop the solution splashing out when it is swirled. ALLOW so that none of the solution is lost when it is swirled (which would make the titre wrong). IGNORE it is more accurate / easier to use / safer (unqualified). DO NOT ALLOW a conical flask measures the volume more accurately (the volume of alkali is measured with the pipette).

Question 3

2 marks

A student has a sample of a drain cleaner that has been diluted with water. It is a dark blue solution that contains sodium hydroxide. She wants to find the volume of dilute hydrochloric acid needed to neutralise 25.0 cm³ of the diluted drain cleaner.

Her teacher tells her to use a pH meter instead of an indicator. She will add the acid from a burette, a small volume at a time, and read the pH meter after each addition.

Explain why an indicator is not suitable for this titration.

Describe how she will know from the pH meter readings when the alkali has just been neutralised.

Model answer

The drain cleaner is dark blue, so the colour of an indicator would be hidden and she would not be able to see the colour change at the end point.
The drain cleaner is alkaline, so at first the pH meter shows a high pH. As she adds acid the pH falls. The alkali has just been neutralised when the pH reaches 7 (the pH drops suddenly to about 7).

Explanation

An indicator only works if its colour change can be seen, which is difficult in a strongly coloured solution. A pH meter measures the pH directly: an alkali has a pH above 7, a neutral solution has a pH of 7 and an acid has a pH below 7. The end point is when the pH reaches 7; near this point a very small volume of acid makes the pH fall quickly.

Mark scheme
  1. 1 mark

    the dark (blue) colour of the drain cleaner would hide / mask the colour of the indicator, so the colour change at the end point could not be seen

    ALLOW the colour change of the indicator would be hard to see in a dark blue solution. IGNORE the indicator would react with the drain cleaner / the indicator is not accurate (unqualified).

  2. 1 mark

    when the pH (falls and) reaches 7 / when the reading shows the solution is neutral

    ALLOW when the pH falls suddenly (from a high value) to about 7. ALLOW when a very small volume of acid makes a big drop in pH, to about 7. DO NOT ALLOW when the pH reaches 0 / 1 / when the solution becomes acidic. IGNORE when the pH changes (unqualified).

Question 4

3 marks

In a titration, the volume of alkali in the conical flask must be exactly 25.0 cm³. A student measures the sodium hydroxide solution with a 25.0 cm³ pipette and a pipette filler.

Describe how she should use the pipette.

Model answer

She rinses the pipette with a little of the sodium hydroxide solution. She uses the pipette filler to draw the solution up into the pipette until it is above the line. She lets the solution out slowly until the bottom of the meniscus is exactly on the line, with her eye level with the line. Then she lets the solution run out into the conical flask, touching the tip on the inside of the flask, and leaves the small drop in the tip.

Explanation

A pipette measures one fixed volume very accurately, but only if it is used correctly. The filler is used for safety, so that no sodium hydroxide solution can get into the mouth, the volume is set by lining up the bottom of the meniscus with the line at eye level, and the pipette is allowed to drain. It is made to deliver 25.0 cm³ with the last small drop left in the tip, so this drop is not blown out.

Mark scheme
  1. 1 mark

    use the pipette filler to draw the sodium hydroxide solution up into the pipette, to above the line / mark

    1 mark for each of points 1 to 4, max 3. ALLOW fill the pipette past the 25.0 cm³ mark using the filler. DO NOT ALLOW sucking the solution up by mouth.

  2. 1 mark

    let the solution out (slowly) until the bottom of the meniscus is (exactly) on the line / mark

    ALLOW with her eye level with the line. ALLOW adjust the level until the bottom of the curved surface of the liquid is on the line. DO NOT ALLOW the top of the meniscus on the line.

  3. 1 mark

    let the solution run (drain) from the pipette into the conical flask

    ALLOW touch the tip of the pipette on the inside of the flask (so that the solution in the tip runs out). DO NOT ALLOW blow out the last drop from the tip (the pipette is made to deliver exactly 25.0 cm³ with this drop left in the tip).

  4. 1 mark

    rinse the pipette with a little of the sodium hydroxide solution (before filling it)

    ALLOW rinse the pipette with distilled water and then with the sodium hydroxide solution. DO NOT ALLOW rinse the pipette only with water (the water left inside would dilute the solution).

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.