Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
Avg
score:
–
Topics
done:
0/25

Electrolysis of copper sulfate solution

Practise 14 exam-style questions on Electrolysis of copper sulfate solution for Edexcel GCSE Combined Science (Foundation Chemistry Paper 1). Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 14 questions
  • 1–6 marks each
  • Instant marking
  • No sign-up needed
14 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

Ella electrolyses copper sulfate solution using graphite electrodes. After a few minutes, one electrode is coated with a pink-brown solid, and bubbles of gas form at the other electrode.

Name the gas.

Model answer

Oxygen.

Explanation

The pink-brown solid is copper, which forms at the cathode because copper is less reactive than hydrogen. At the graphite anode the sulfate ions are not discharged, so oxygen forms from the water instead. Hydrogen is a common wrong answer, but hydrogen could only form at the cathode, where copper forms instead.

Mark scheme
  1. 1 mark

    oxygen

    accept O₂. do not accept hydrogen, sulfur dioxide, sulfur or carbon dioxide. ignore the name of the electrode, even if it is wrong.

Question 2

2 marks

In a copper refinery, an impure copper anode has a mass of 380 kg. The anode is 99.2% copper by mass.

Calculate the mass of impurities in the anode.

Model answer

Percentage of impurities = 100 − 99.2 = 0.8 %
Mass of impurities = 0.8 ÷ 100 × 380 = 3.04 kg

Explanation

The impurities are the part that is not copper: 100 − 99.2 = 0.8 % of the mass. Then find 0.8 % of 380 kg. Another correct method is to work out the mass of copper (376.96 kg) and subtract it from 380 kg; stopping at 376.96 kg is the common error.

Mark scheme
  1. 1 mark

    (percentage of impurities =) 100 − 99.2 = 0.8 (%) / (mass of copper =) 99.2 ÷ 100 × 380 = 376.96 (kg); or a correct final answer of 3.04 kg with no working

    An answer of 3.04 kg with no working scores 2 marks. An answer of 376.96 kg (the mass of copper, not the impurities) scores 1 mark.

  2. 1 mark

    3.04 (kg)

    accept 0.8 ÷ 100 × 380 = 3.04 or 380 − 376.96 = 3.04. accept 3.0 kg. Ignore units.

Question 3

2 marks

In an experiment to find how the current affects the change in mass of copper electrodes, a student:
- rubs each copper electrode with emery paper before weighing it
- adjusts a variable resistor during the experiment while watching the ammeter.

Give a reason for each of these steps.

Model answer

The emery paper removes any oxide layer or dirt from the surface of each electrode, so the surface is clean copper.
The variable resistor is adjusted to keep the current at the chosen value throughout the experiment.

Explanation

A clean surface means copper dissolves from the anode and is deposited on the cathode evenly, and dirt does not affect the masses. The current can drift as the experiment runs, so the variable resistor is used to keep it constant, because the mass of copper deposited depends on the current. The ammeter measures the current; it does not control it.

Mark scheme
  1. 1 mark

    (emery paper) to remove any (oxide) layer / dirt / grease from the surface of the electrode

    accept to clean the electrode (so that copper can dissolve from it / be deposited on it evenly). ignore 'to make it smooth' or 'to make it shiny' with no idea of cleaning.

  2. 1 mark

    (variable resistor) to keep the current constant / at the value chosen

    accept to set or adjust the current to the value needed. do not accept 'to measure the current' (that is the ammeter's job).

Question 4

4 marks

Sanjay investigates how the current affects the increase in mass of a copper cathode in copper sulfate solution. He passes each current for 15 minutes.

This is part of his method:
- he uses a balance that reads to the nearest 0.1 g
- he tests each current only once
- he takes the cathode out of the solution and weighs it straight away.

All his increases in mass are between 0.0 g and 0.2 g, and they do not show a clear pattern.

Suggest two improvements to Sanjay's method. Explain how each improvement would give better results.

Model answer

Use a balance that reads to 0.01 g. The changes in mass are very small (less than 0.2 g), so a balance that reads to only 0.1 g cannot show the differences between the currents.
Rinse the cathode with distilled water and let it dry completely before weighing it. Solution left on the cathode adds extra mass, so the increase in mass would be too large and would vary from test to test.

Explanation

Each improvement should be linked to a weakness in the method and to why it gives better results. A balance reading to 0.1 g is not precise enough for changes this small; a wet cathode weighs more than the copper on it; repeating each current and finding a mean reduces the effect of random errors. Vague reasons such as 'to make it more accurate' do not score on their own.

Mark scheme
  1. 1 mark

    use a balance that reads to 0.01 g (or 0.001 g) / a more precise balance

    Max 4: 1 mark for each improvement and 1 mark for its linked explanation, for up to two improvements. Max 2 if only one improvement is given. Credit another valid improvement with a linked explanation in place of one pair, for example using a variable resistor to keep the current constant, because the current affects the mass deposited.

  2. 1 mark

    because the changes in mass are very small, so a balance reading to 0.1 g cannot measure them precisely / cannot show small differences between the currents

    accept the readings would be more precise / have a higher resolution.

  3. 1 mark

    repeat each current (at least three times) and calculate a mean

    accept repeat the experiment and find an average for each current.

  4. 1 mark

    to reduce the effect of random errors / so that anomalous results can be spotted (and left out of the mean) / to make the results more repeatable

    ignore 'to make it more accurate' or 'to make it a fair test' on their own.

  5. 1 mark

    rinse the cathode with distilled water and dry it before weighing

    accept dry it (for example by dipping it in propanone, using a hairdryer or leaving it to dry) before weighing.

  6. 1 mark

    because solution or water left on the cathode adds to its mass, so the increase in mass would be too large / would be different each time

    accept so that only the mass of the copper deposited is measured.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.