Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
OCR GCSE Physics (Paper 3) Smart practice A mixed round aimed at your weak spots
Unit 1
Matter
Unit 2
Forces
Unit 3
Electricity
Unit 4
Magnetism and magnetic fields
Unit 9
Practical skills
Avg
score:
–
Topics
done:
0/36

The motor effect and electric motors

Practise 17 exam-style questions on The motor effect and electric motors for OCR GCSE Physics (Paper 3). Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 17 questions
  • 1–6 marks each
  • Instant marking
  • No sign-up needed
17 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

A wire carrying a current of 2.5 A is at right angles to a uniform magnetic field. The length of wire in the field is 8.0 cm. The force on the wire is 0.060 N.

What is the magnetic flux density of the field?

Use the equation: force on a conductor (at right angles to a magnetic field) carrying a current = magnetic flux density × current × length

Choose your answer.

  • A 0.0030 T
  • B 0.012 T
  • C 0.30 T
  • D 3.3 T

Model answer

C (B = F ÷ (I × l) = 0.060 ÷ (2.5 × 0.080) = 0.30 T)

Explanation

Rearrange F = B × I × l to give B = F ÷ (I × l), and convert the length to metres first: 8.0 cm = 0.080 m. Each wrong option comes from a common slip: leaving the length in centimetres, multiplying instead of dividing, or turning the fraction upside down.

Mark scheme
  1. 1 mark

    C / 0.30 T

    The only correct answer is C: magnetic flux density = force ÷ (current × length) = 0.060 ÷ (2.5 × 0.080) = 0.30 T. A is not correct because it uses the length in cm (0.060 ÷ (2.5 × 8.0) = 0.0030); B is not correct because it multiplies the three values (0.060 × 2.5 × 0.080 = 0.012); D is not correct because it inverts the rearrangement ((2.5 × 0.080) ÷ 0.060 = 3.3). ALLOW the letter or the option. If more than one option is given, do not award the mark.

Question 2

2 marks

A magnet hangs from a newtonmeter. The magnet has two flat poles, X and Y, facing each other across a gap: X is on the north side of the gap and Y is on the south side, so the field in the gap is horizontal.

A horizontal wire, fixed to a stand, passes through the gap without touching the magnet. The wire runs east-west, and the current in it flows towards the east. When the current is switched on, the reading on the newtonmeter increases.

Deduce which pole, X or Y, is the north pole. Explain your answer.

Model answer

The newtonmeter reading increases, so there is an extra downward force on the magnet. The magnet and the wire exert equal and opposite forces on one another, so the force on the wire is upwards.
Using Fleming's left-hand rule: thumb (force on the wire) pointing up, second finger (current) pointing east, so the first finger (field) points north. The field in the gap goes from Y, on the south side, to X, on the north side. A magnetic field goes from a north pole to a south pole, so Y is the north pole.

Explanation

This needs two steps. First, the force on the magnet is equal and opposite to the force on the wire, so a downward force on the magnet means an upward force on the wire. Then Fleming's left-hand rule, with two directions known, gives the third: the field points north, from Y to X. A common error is to apply the rule to the force on the magnet instead of the force on the wire.

Mark scheme
  1. 1 mark

    the force on the magnet is downwards, so the force on the wire is upwards (the magnet and the wire exert equal and opposite forces on one another)

    ALLOW the wire is pushed up because the magnet is pushed down. The direction of the force on the wire is needed.

  2. 1 mark

    Y, because Fleming's left-hand rule with the thumb (force) up and the second finger (current) east gives a field (first finger) pointing north, from Y to X, and the field goes from the north pole to the south pole

    Y with no reasoning does not score. ALLOW ECF from a downward force on the wire in marking point 1: X, with a correct use of Fleming's left-hand rule. ALLOW fore finger / index finger for first finger and middle finger for second finger.

Question 3

3 marks

In a jumping wire demonstration, a bare copper wire rests across the narrow gap between two strong flat magnets, at right angles to the magnetic field in the gap. When the current is switched on, the wire jumps upwards.

5.0 cm of the wire is in the field. The field in the gap has a magnetic flux density of 0.18 T. The current is 3.2 A.

Calculate the force on the wire.

Use the equation: force on a conductor (at right angles to a magnetic field) carrying a current = magnetic flux density × current × length

Give your answer to 2 significant figures.

Model answer

Length in the field = 5.0 cm = 0.050 m
Force = magnetic flux density × current × length
= 0.18 × 3.2 × 0.050
= 0.0288 N
= 0.029 N (to 2 significant figures)

Explanation

Substitute into F = B × I × l with every quantity in SI units: the length must be in metres. Leaving the length in centimetres gives an answer 100 times too big (2.88 N). Round only at the end: 0.0288 N becomes 0.029 N to 2 significant figures, because the zeros before the 2 do not count.

Mark scheme
  1. 1 mark

    substitution with the length in metres: (F =) 0.18 × 3.2 × 0.050; or a correct final answer of 0.029 N (or 0.0288 N) with no working

    An answer of 0.029 N with no working scores 3 marks. ALLOW 2 marks for 0.0288 N given as the final answer. ALLOW 2 marks for 2.9 N (length left in cm), and 1 mark for 2.88 N. ALLOW 29 mN.

  2. 1 mark

    (F =) 0.0288 (N); or a correct final answer of 0.029 N with no working

    ALLOW 2.88 × 10⁻² (N).

  3. 1 mark

    evaluation: 0.029 (N) to 2 significant figures

    ALLOW 2.9 × 10⁻² (N). ALLOW ECF for the significant-figure mark from a valid calculation, for example 2.88 given as 2.9. DO NOT ALLOW 0.03 (1 significant figure).

Question 4

4 marks

An engineer is designing a small linear motor. A straight wire carrying a current of 1.5 A must have a force of 0.090 N on it.

The wire passes through the gaps of a row of identical magnets placed side by side. Each magnet produces a uniform magnetic field of magnetic flux density 0.20 T, at right angles to the wire, along 2.0 cm of the wire.

Calculate the number of magnets needed.

Use the equation: force on a conductor (at right angles to a magnetic field) carrying a current = magnetic flux density × current × length

Model answer

Length of wire needed in the field: l = F ÷ (B × I)
= 0.090 ÷ (0.20 × 1.5)
= 0.090 ÷ 0.30
= 0.30 m = 30 cm
Each magnet covers 2.0 cm of the wire, so the number of magnets = 30 ÷ 2.0 = 15 magnets.

Explanation

Rearrange F = B × I × l to find the length of wire that must be in the field, then divide by the length of wire that each magnet covers, using the same units for both lengths. The force is proportional to the length of wire in the field, so adding magnets in a row increases the force. A common slip is to divide 0.30 m by 2.0 cm without converting, which gives 0.15.

Mark scheme
  1. 1 mark

    rearrangement: length = force ÷ (magnetic flux density × current); or a correct final answer of 15 magnets with no working

    An answer of 15 magnets with no working scores 4 marks. ALLOW l = F ÷ (B × I) in symbols. ALLOW 3 marks for a length of 0.30 m / 30 cm with no number of magnets.

  2. 1 mark

    substitution: (l =) 0.090 ÷ (0.20 × 1.5); or a correct final answer of 15 magnets with no working

    ALLOW 0.090 ÷ 0.30.

  3. 1 mark

    length of wire in the field = 0.30 m / 30 cm; or a correct final answer of 15 magnets with no working

    ALLOW 0.3 m.

  4. 1 mark

    evaluation: number of magnets = 30 ÷ 2.0 = 15

    ALLOW ECF for the number of magnets from a wrongly calculated length divided by 2.0 cm (with consistent units), rounded up to a whole number. DO NOT ALLOW 0.15 (0.30 m divided by 2.0 cm without converting).

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.