Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
AQA GCSE Combined Science (Foundation Physics Paper 1) Smart practice A mixed round aimed at your weak spots
Unit 18
Energy
Energy changes in a system, and the ways energy is stored before and after such changes
Energy stores and systems, and changes in energy
Energy changes in systems
Power
Conservation and dissipation of energy
Energy transfers in a system and efficiency
National and global energy resources
National and global energy resources
Unit 19
Electricity
Unit 20
Particle model of matter
Changes of state and the particle model
Density of materials and changes of state
Particle model and pressure
Particle motion in gases
Unit 21
Atomic structure
Avg
score:
–
Topics
done:
0/17

Series and parallel circuits

Practise 22 exam-style questions on Series and parallel circuits for AQA GCSE Combined Science (Foundation Physics Paper 1). Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 22 questions
  • 1–6 marks each
  • Instant marking
  • No sign-up needed
20 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

A 22 Ω resistor and a 47 Ω resistor are connected in series.

Calculate the total resistance of the two resistors.

Use the equation:

total resistance = R₁ + R₂

Model answer

total resistance = 22 + 47 = 69 Ω

Explanation

For resistors in series the total resistance is the sum of the individual resistances: 22 + 47 = 69 Ω. The total is always greater than the largest single resistance, because the current has to pass through both resistors.

Mark scheme
  1. 1 mark

    69 (Ω)

    A correct answer with no working scores full marks. Do not accept 25 (from subtracting) or 1034 (from multiplying).

Question 2

2 marks

The diagram shows two lamps connected in parallel to a battery.

Lamp L₁ is lit but lamp L₂ is not lit.

Use the diagram to explain why.

Circuit diagram. Going round the loop from the + terminal of the battery: two branches in parallel (one branch has lamp L₁ then switch S₁ (closed); the other branch has lamp L₂ then switch S₂ (open)); and back to the − terminal of the battery.

Model answer

Switch S₂ is open, so L₂'s branch is not a complete circuit and there is no current in L₂. Switch S₁ is closed, so L₁'s branch is still a complete circuit with the battery and L₁ lights. In a parallel circuit each branch works independently.

Explanation

Each branch of a parallel circuit is connected separately across the battery. An open switch breaks only its own branch, so L₂ goes out while L₁ keeps the full potential difference and stays lit. In a series circuit, one open switch would turn off every lamp.

Mark scheme
  1. 1 mark

    switch S₂ (in the branch with L₂) is open, so there is no current in L₂

    Allow L₂'s branch is not a complete circuit. 'S₂ is open' with no link to the current in L₂ (or L₂'s branch being incomplete) does not score. Ignore 'L₂ is broken'.

  2. 1 mark

    the branch with L₁ (and the closed switch S₁) is still a complete circuit with the battery, so there is a current in L₁

    Allow each branch of a parallel circuit works independently / opening one branch does not affect the other branch.

Question 3

3 marks

The diagram shows two lamps, L₁ and L₂, connected in series with a battery.

Describe how a student could use a voltmeter to show that the potential difference of the battery is shared between the two lamps.

Circuit diagram. All the components are connected in series in a single loop. Going round the loop from the + terminal of the battery: lamp L₁; then lamp L₂; then a closed switch; and back to the − terminal of the battery.

Model answer

Connect the voltmeter across L₁ (in parallel with it) and record the reading. Then connect it across L₂ and record the reading, and then across the battery. The potential difference across L₁ plus the potential difference across L₂ equals the potential difference across the battery, which shows that the battery's potential difference is shared between the lamps.

Explanation

A voltmeter must be connected in parallel with the component it measures. Measuring across each lamp in turn, and across the battery, lets the student check that the two lamp readings add up to the battery's potential difference. This is one way of using meters to check a d.c. series circuit.

Mark scheme
  1. 1 mark

    connect the voltmeter in parallel with / across L₁ and record the reading

    Allow the use of two or three voltmeters. Do not accept connecting the voltmeter in series.

  2. 1 mark

    connect the voltmeter across L₂ and across the battery, recording each reading

    Allow measure the potential difference across each lamp and across the battery.

  3. 1 mark

    the potential differences across L₁ and L₂ add up to the potential difference across the battery

    Allow the two lamp readings add up to the battery's potential difference. Ignore 'the readings are the same'.

Question 4

4 marks

An LED is connected in series with a resistor R and a 9.0 V battery. The potential difference across the LED is 2.0 V and the current in the circuit is 20 mA.

Calculate the resistance of R.

Use the equation:

potential difference = current × resistance

Circuit diagram. Going round the loop from the + terminal of the battery (labelled 9.0 V): an LED pointing forwards (its triangle points the way we are going round), with a voltmeter (reading 2.0 V) connected across it; then resistor R; then an ammeter (reading 20 mA); and back to the − terminal of the battery.

Model answer

potential difference across R = 9.0 - 2.0 = 7.0 V
20 mA = 0.020 A
7.0 = 0.020 × resistance
resistance = 7.0 ÷ 0.020 = 350 Ω

Explanation

In series the battery's 9.0 V is shared, so the resistor has 9.0 - 2.0 = 7.0 V across it. The current is the same everywhere in a series circuit, 20 mA = 0.020 A, so the resistance is 7.0 ÷ 0.020 = 350 Ω. The resistor limits the current so that the LED is not damaged.

Mark scheme
  1. 1 mark

    potential difference across R = 9.0 - 2.0 = 7.0 (V)

    A correct answer with no working scores full marks. Full marks are not awarded for a correct final answer from incorrect working.

  2. 1 mark

    20 mA = 0.020 A

    Allow 0.02 A.

  3. 1 mark

    7.0 = 0.020 × resistance / resistance = 7.0 ÷ 0.020

    Allow ecf from their potential difference. Allow a correct substitution using an incorrectly / not converted value of current.

  4. 1 mark

    resistance = 350 (Ω)

    Allow ecf: an error is penalised once only, so 450 Ω (using 9.0 V instead of 7.0 V) scores 3 marks, 0.35 Ω (current not converted) scores 3 marks and 0.45 Ω (both errors) scores 2 marks.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Revision notes

Series and parallel circuits

The big idea

Components can be joined in two ways: in series, one after another in a single loop, or in parallel, on separate branches. The current, the potential difference and the total resistance follow different rules in each, and many circuits have both series and parallel parts. Know the rules and you can work out every meter reading.

The rules

SeriesParallel
Paths for the currentOne loopA separate branch for each component
CurrentThe same through each componentThe total current is the sum of the branch currents
Potential differenceThe supply's p.d. is shared between the componentsThe p.d. across each branch is the same
Total resistanceThe sum of the resistancesLess than the smallest resistance
If one lamp breaksEvery lamp goes outThe other branches keep working

For two resistors in series:

\[R_{\text{total}} = R_1 + R_2\]
  • resistance, \(R\), in ohms, Ω

This rule is not on the equation sheet, so learn it. It works for any number of resistors in series. You never have to calculate the total resistance of resistors in parallel.

In series, the p.d. is shared in the same ratio as the resistances: the larger resistor gets the larger share, because the same current flows through both (\(V = IR\)).

Circuit diagram. Going round the loop from the + terminal of the battery (labelled 6.0 V), in the direction conventional current flows: ammeter A₁ (reading 0.75 A); then two branches in parallel (one branch has lamp L then ammeter A₂ (reading 0.50 A); the other branch has resistor R then ammeter A₃ (reading 0.25 A)), with voltmeter V (reading 6.0 V) connected across this parallel section; then a closed switch; and back to the − terminal of the battery.
Each branch has the full 6.0 V across it, and the branch currents add up to the current from the battery.

Why the total resistance changes

  • Adding a resistor in series makes the charge pass through one more resistor in turn. The supply's p.d. is shared between more resistors, so for the same supply the current is smaller: the total resistance has increased.
  • Adding a resistor in parallel gives the charge an extra path. The new branch has the full supply p.d. across it and carries extra current, so the total current from the same supply is larger: the total resistance has decreased.

Calculating in series circuits

Replace series resistors with one equivalent resistance (their sum), find the current from the supply's p.d., then use \(V = IR\) for each component.

Making up a resistance

A technician needs a total resistance of at least 50 Ω, but she only has 22 Ω resistors. She joins them in series to a 6.0 V battery. How many resistors does she need, and what current flows?

In series the resistances add. Two give \(22 + 22 = 44\ \Omega\), which is too small, so she needs three: \(R_{\text{total}} = 22 + 22 + 22 = 66\ \Omega\)

\(I = \dfrac{V}{R_{\text{total}}} = \dfrac{6.0}{66} = 0.0909\ldots\), so \(I = 0.091\) A (2 significant figures), the same through each resistor

Each resistor has \(V = IR = 0.0909 \times 22 = 2.0\) V across it, and the three p.d.s add up to the supply's 6.0 V.

A car's electrical system

A car's two headlamps, each with a resistance of 2.4 Ω, are connected in parallel to its 12 V battery. The driver then switches on a heated seat with a resistance of 4.0 Ω, on another parallel branch. Show that switching on the seat decreases the total resistance of the circuit.

Each branch has the full 12 V across it, so each headlamp takes \(I = \dfrac{V}{R} = \dfrac{12}{2.4} = 5.0\) A

Headlamps only: total current \(= 5.0 + 5.0 = 10\) A, so the total resistance is \(\dfrac{12}{10} = 1.2\ \Omega\)

The seat takes \(\dfrac{12}{4.0} = 3.0\) A, so the total current rises to 13 A and the total resistance falls to \(\dfrac{12}{13} = 0.92\ \Omega\) (2 significant figures)

The new branch gives the charge an extra path, so more current flows from the same p.d.: the total resistance has decreased.

Series circuits for measuring and testing

  • To measure a component's resistance, put an ammeter in series with it and a voltmeter across it, then use \(R = V \div I\). An ammeter has a very low resistance so it hardly changes the current; a voltmeter has a very high resistance so it takes almost no current.
  • A continuity tester is a battery, a lamp (or buzzer) and two probes in series. Touch the probes to each end of a fuse or a wire: if the lamp lights, the loop is complete; if not, there is a break.
  • Sensor circuits put a thermistor or an LDR in series with a fixed resistor. When the sensor's resistance changes, the share of the supply p.d. across each part changes (see also: Resistors).

Common mistakes

  • Splitting the supply p.d. between parallel branches. In parallel, each branch has the full supply p.d.
  • Adding resistances that are in parallel. Adding only works for series; in parallel the total is less than the smallest.
  • Saying the current is the same in each branch of a parallel circuit. It only splits equally if the branches are identical.
  • Adding kilohms to ohms without converting: 2.2 kΩ is 2200 Ω.
  • Using one resistor's value with the supply p.d. in a series circuit. Use the total resistance to find the current.

Exam tip

In "explain what happens to the brightness" questions, work through the chain in order: total resistance, then current, then the p.d. across each component, then brightness. In calculations, label each current and p.d. with the component it belongs to, then check: the p.d.s round a series loop add up to the supply p.d., and the branch currents add up to the total current.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.