Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
Edexcel GCSE Chemistry (Paper 1) Smart practice A mixed round aimed at your weak spots
Unit 1
Key concepts in chemistry
Unit 2
States of matter and mixtures
Unit 3
Chemical changes
Unit 4
Extracting metals and equilibria
Unit 5
Separate chemistry 1
Avg
score:
–
Topics
done:
0/33

The Haber process and industrial conditions

Practise 15 exam-style questions on The Haber process and industrial conditions for Edexcel GCSE Chemistry (Paper 1). Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 15 questions
  • 1–6 marks each
  • Instant marking
  • No sign-up needed
15 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

In the Haber process, nitrogen and hydrogen react to form ammonia.

N₂(g) + 3H₂(g) ⇌ 2NH₃(g)

The gases are fed into the reactor with 1 molecule of nitrogen for every 3 molecules of hydrogen.

Give a reason why this ratio is used.

Model answer

1 molecule of nitrogen reacts with 3 molecules of hydrogen (N₂ + 3H₂), so feeding the gases in this ratio means neither gas is left in excess.

Explanation

The balancing numbers in the equation give the ratio in which the molecules react. Supplying the gases in the same ratio avoids building up an excess of one of them in the recycled gas. Nitrogen comes from the air and hydrogen from natural gas, so neither is 'free' to waste.

Mark scheme
  1. 1 mark

    it is the ratio in which nitrogen and hydrogen react / it matches the (balancing numbers in the) equation, so neither gas is in excess / wasted (1)

    Accept '1 mole of nitrogen reacts with 3 moles of hydrogen', 'so that there is no excess of either reactant'. Ignore 'to make more ammonia' or 'to get a higher yield' on their own. Do not accept 'because hydrogen is cheaper' or 'because there is more hydrogen in the air'.

Question 2

2 marks

At 450 °C, the percentage of ammonia in the equilibrium mixture would be about 70% at a pressure of 1000 atm, compared with about 26% at 200 atm. Equilibrium would also be reached more quickly at 1000 atm.

Suggest two reasons why the Haber process is not carried out at 1000 atm.

Model answer

Compressing the gases to 1000 atm would use a very large amount of energy, which would be expensive. The reactor and pipes would also have to be much stronger and thicker to withstand the pressure, so the plant would cost much more to build, and there would be a greater risk of dangerous leaks or explosions.

Explanation

A very high pressure improves both the rate and the equilibrium yield, so the reasons against it are about cost and safety: the energy needed to compress the gases and the strength of the equipment. 200 atm gives an acceptable yield at an acceptable cost. Answers about yield or rate miss the point, because both would be better at 1000 atm.

Mark scheme
  1. 1 mark

    compressing the gases to a very high pressure needs a lot of energy / electricity, which is expensive (1)

    Any two from the three points; max 2. Ignore 'it is too expensive' with no reason.

  2. 1 mark

    the reactor, pipes and pumps would need to be much stronger / thicker walled, which costs more to build and maintain (1)

    Accept 'expensive equipment is needed to withstand the pressure'.

  3. 1 mark

    very high pressure is more dangerous / greater risk of leaks or explosions (1)

    Accept 'it is a safety hazard'. Do not accept 'the yield would be too low' or 'the reaction would be too slow'.

Question 3

3 marks

A scientist used a small test reactor to make ammonia at 200 atm with an iron catalyst. Each time, she filled the reactor with the same amounts of nitrogen and hydrogen, waited until equilibrium was reached, then emptied it.

- At 400 °C, equilibrium was reached after 20 minutes. The reactor then contained 3.6 kg of ammonia.
- At 450 °C, equilibrium was reached after 8 minutes. The reactor then contained 2.6 kg of ammonia.

Assume that emptying and refilling the reactor takes no time.

Show that more ammonia is made in 2 hours at 450 °C than at 400 °C.

Model answer

number of fills in 2 hours (120 minutes):
at 400 °C: 120 ÷ 20 = 6 fills; at 450 °C: 120 ÷ 8 = 15 fills
mass of ammonia made in 2 hours:
at 400 °C: 6 × 3.6 = 21.6 kg; at 450 °C: 15 × 2.6 = 39.0 kg
39.0 kg is more than 21.6 kg, so about 1.8 times as much ammonia is made at 450 °C, even though each fill contains less ammonia at equilibrium.

Explanation

At the lower temperature the equilibrium mixture contains more ammonia, but equilibrium is reached much more slowly, so fewer batches can be made in the same time. Working out the mass made in a fixed time shows why industry chooses a temperature that gives an acceptable yield in an acceptable time. Comparing only the 3.6 kg and 2.6 kg ignores the time taken.

Mark scheme
  1. 1 mark

    (number of fills in 2 hours =) 120 ÷ 20 = 6 at 400 °C and 120 ÷ 8 = 15 at 450 °C (1)

    Show that: the working must be seen; a statement that 450 °C makes more with no calculation scores 0. Alternative method: rate of production = 3.6 ÷ 20 = 0.18 kg per minute and 2.6 ÷ 8 = 0.325 kg per minute (MP1 and MP2), then MP3. Accept a calculation for 1 hour (3 and 7.5 fills; 10.8 kg and 19.5 kg) for MP1 and MP2.

  2. 1 mark

    (mass of ammonia in 2 hours =) 6 × 3.6 = 21.6 kg at 400 °C and 15 × 2.6 = 39(.0) kg at 450 °C (1)

    Allow ECF from incorrect numbers of fills.

  3. 1 mark

    39 kg is greater than 21.6 kg, so 450 °C makes more ammonia (about 1.8 times as much), even though each fill contains less ammonia (1)

    A comparison of the two calculated values is needed. Accept 'the faster rate at 450 °C more than makes up for the lower yield'.

Question 4

4 marks

Hydrogen for making ammonia can also come from other industrial processes, as a by-product. A chemical company makes chlorine by the electrolysis of sodium chloride solution, and hydrogen forms at the same time.

2NaCl + 2H₂O → 2NaOH + H₂ + Cl₂

The company sells the hydrogen to a nearby ammonia plant, where it reacts with nitrogen.

N₂ + 3H₂ ⇌ 2NH₃

(relative atomic masses: H = 1.0, N = 14, Cl = 35.5)

Calculate the maximum mass of ammonia, in kg, that the hydrogen formed with 1.00 tonne of chlorine could produce.

(1 tonne = 1 000 000 g)

Model answer

relative formula masses: Cl₂ = 2 × 35.5 = 71; NH₃ = 14 + (3 × 1.0) = 17
moles of Cl₂ = 1 000 000 ÷ 71 = 14 085 mol
from the first equation, 1 mol of H₂ forms with each 1 mol of Cl₂, so moles of H₂ = 14 085 mol
from the second equation, 3 mol of H₂ make 2 mol of NH₃, so moles of NH₃ = 14 085 × 2 ÷ 3 = 9390 mol
mass of NH₃ = 9390 × 17 = 159 630 g = 160 kg

Explanation

Work along the chain from chlorine to hydrogen to ammonia: each mole of chlorine made comes with one mole of hydrogen, and 3 mol of hydrogen make 2 mol of ammonia. The answer is a maximum, because it assumes that all of the hydrogen is converted into ammonia; using a by-product like this gives the ammonia plant a readily available source of hydrogen. Common errors are using 35.5 instead of 71 for chlorine, Cl₂, and leaving out or inverting the 3 : 2 ratio.

Mark scheme
  1. 1 mark

    (moles of Cl₂ =) 1 000 000 ÷ 71 = 14 100 / 14 085 (mol) (1)

    An answer of 160 kg with no working scores 4 marks. Accept 159 to 160 kg (rounding during the working). Allow ECF throughout. Accept working in tonne-moles or kg (e.g. 1000 kg ÷ 71 = 14.1 kmol). Alternative method by mass ratio: 71 g of Cl₂ forms with 2.0 g of H₂, and 6.0 g of H₂ makes 34 g of NH₃ (MP1, MP2 and MP3), so mass of ammonia = 1000 × (2.0 ÷ 71) × (34 ÷ 6.0) = 159.6 kg (MP4). An answer of 239 kg (the 3 : 2 ratio not used) or 359 kg (the ratio used the wrong way round) scores 3 marks (MP1, MP2 and MP4 by ECF). An answer of 319 kg (35.5 used for Cl₂) scores 3 marks (MP2, MP3 and MP4 by ECF). An answer of 28.2 kg (the mass of hydrogen, not ammonia) scores MP1 and MP2.

  2. 1 mark

    (moles of H₂ = moles of Cl₂ =) 14 100 / 14 085 (mol) (1)

    for using the 1 : 1 ratio of H₂ to Cl₂ from the electrolysis equation

  3. 1 mark

    (moles of NH₃ = 14 085 × 2 ÷ 3 =) 9390 (mol) (1)

    for using the 3 : 2 ratio of H₂ to NH₃; accept 9389 / 9400 mol

  4. 1 mark

    (mass of NH₃ = 9390 × 17 = 159 600 g =) 160 (kg) (1)

    Accept 159 / 159.6 / 159.8 / 160 kg. Allow 159 600 g or 0.160 tonnes only if the unit is given.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.