Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
Avg
score:
–
Topics
done:
0/23

Practical skills: planning and making measurements

Practise 15 exam-style questions on Practical skills: planning and making measurements for OCR GCSE Combined Science (Chemistry Paper 4). Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 15 questions
  • 1–6 marks each
  • Instant marking
  • No sign-up needed
15 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

A student wants to measure the boiling point of a sample of nonane. Nonane is a liquid alkane. Its boiling point is about 151 °C.

She has four thermometers.

Which thermometer should she use?

Choose your answer.

  • A −10 °C to 50 °C, marked every 0.1 °C
  • B −10 °C to 110 °C, marked every 0.5 °C
  • C 0 °C to 100 °C, marked every 0.2 °C
  • D 0 °C to 360 °C, marked every 1 °C

Model answer

D

Explanation

First check the range: a thermometer can only measure temperatures inside its scale, and heating it above its highest reading could break it. Only thermometer D goes above 151 °C. A common mistake is to choose the thermometer with the smallest divisions (A) without checking whether its range is big enough.

Mark scheme
  1. 1 mark

    D / 0 °C to 360 °C, marked every 1 °C

    The only correct answer is D: it is the only thermometer whose range goes above 151 °C, so it is the only one that can measure the boiling point of nonane. A is not correct because its highest reading is 50 °C, even though it has the smallest divisions; B is not correct because its highest reading is 110 °C, which is below 151 °C; C is not correct because its highest reading is 100 °C, which is also below 151 °C. ALLOW the letter or the option. If more than one option is given, do not award the mark.

Question 2

2 marks

A teacher shows that heating blue hydrated copper sulfate is a reversible reaction:

hydrated copper sulfate ⇌ anhydrous copper sulfate + water

She puts some blue crystals in a boiling tube and clamps the tube so that its open end is slightly lower than its closed end. She heats the crystals with a Bunsen burner. The crystals turn into a white powder, and drops of liquid water collect near the open end of the tube.

Explain why she clamps the tube with its open end pointing slightly downwards.

Model answer

When the crystals are heated, the water in them is given off as steam. The open end of the tube is not heated, so it is cooler, and the steam condenses there into drops of liquid water. Because the open end points slightly downwards, the drops cannot run back. If cold water ran back onto the hot glass, the tube could crack, and the water would also react with the white anhydrous copper sulfate and turn it blue again.

Explanation

When a solid that gives off water is heated in a tube, the steam condenses in the cool part of the tube near the open end. Clamping the tube with the open end slightly lower stops this liquid running back onto the hottest glass, where the sudden cooling could crack it. In this reversible reaction, water that ran back would also turn the white anhydrous copper sulfate blue again.

Mark scheme
  1. 1 mark

    the water is given off as steam (water vapour), which cools and condenses into liquid water in the cooler part of the tube near the open end (the part that is not heated)

    1 mark for each of points 1 to 3, max 2. ALLOW the water vapour turns back into a liquid at the open end because it is cooler there. IGNORE 'so that the water can escape' on its own.

  2. 1 mark

    if the open end pointed upwards, the (cold) liquid water would run back down onto the hot glass, which could crack the tube

    ALLOW so that the water runs away from the hot part of the tube / does not run back onto the hot part of the tube. IGNORE 'for safety' on its own.

  3. 1 mark

    water that ran back would react with the white anhydrous copper sulfate again (the reverse reaction) and turn it blue again, so the solid would not all stay white

    ALLOW the water would turn the white powder back to blue / would make hydrated copper sulfate again.

Question 3

2 marks

A student needs to warm some copper sulfate solution to 50 °C before she adds iron filings to it. She heats the solution in a glass beaker standing on an electric hotplate.

To check the temperature, she holds a thermometer so that its bulb rests on the bottom of the beaker.

Explain why her temperature readings will not be accurate.

Suggest how she should use the thermometer instead.

Model answer

The bottom of the beaker sits on the hotplate, so the glass there is much hotter than the solution. The thermometer bulb is touching the hot glass, so it shows a temperature that is too high, not the temperature of the solution.
She should hold the thermometer in a clamp so that the bulb is in the middle of the solution, not touching the glass, and stir the solution before she reads the temperature.

Explanation

A thermometer measures the temperature of whatever its bulb touches. On a hotplate the bottom of the beaker is the hottest part, so the bulb must be in the liquid itself, away from the glass, and the liquid should be stirred so it is the same temperature all through. This is about the accuracy of the measurement: the readings would be too high every time.

Mark scheme
  1. 1 mark

    the bottom of the beaker is heated directly by the hotplate, so it is hotter than the solution / the thermometer measures the temperature of the glass (not the solution), so the readings will be too high

    ALLOW the bulb is touching the hot glass, so the reading is not the temperature of the solution. ALLOW the solution is hottest at the bottom (it is not all at the same temperature). DO NOT ALLOW the thermometer could break (this is about safety, not accuracy) for this point.

  2. 1 mark

    hold (or clamp) the thermometer so that its bulb is in the middle of the solution, not touching the glass (and stir the solution before reading it)

    ALLOW keep the bulb in the solution but away from the bottom and sides of the beaker. ALLOW stir the solution so that it is all at the same temperature, then read the thermometer. IGNORE read it at eye level.

Question 4

4 marks

Particulates are tiny solid particles in the air, such as soot.

A city council thinks that road traffic is a major source of particulates in the city. It puts 12 sensors in different places, for example beside busy roads, in parks and outside schools. Each sensor measures the particulates in the air every hour for a whole year.

Write a hypothesis that the council could test with its results. Use your knowledge of how particulates are produced.

Explain why the council uses sensors in many different places and takes readings every hour for a year, rather than using one sensor for one day.

Model answer

Hypothesis: the level of particulates is higher at sensors beside busy roads than at sensors in parks, because vehicle engines burn diesel and petrol, and incomplete combustion of the fuel releases soot.
The level of particulates is different in different parts of the city, so sensors in many places give results that represent the whole city, not just one street. The level also changes with the time of day (it is higher in the rush hour), the day of the week, the season and the weather, so hourly readings for a whole year show the typical levels and give a reliable mean, instead of one day that might be unusual.

Explanation

A hypothesis is a testable idea with a scientific reason: here, more traffic means more particulates, because engines release soot when fuel burns incompletely. The sampling must be representative: particulate levels vary from place to place and from hour to hour, so many sites and many readings over a long time are needed. Saying only 'to make it fair' or 'more accurate' does not explain the choice.

Mark scheme
  1. 1 mark

    (hypothesis) the level of particulates is higher beside busy roads than in places with less traffic (such as parks) / the more traffic there is, the higher the level of particulates

    Points 1 and 2 are for the hypothesis; points 3 and 4 are for the explanation. ALLOW particulate levels are higher at times of heavy traffic, such as rush hour. The hypothesis must link the amount of traffic to the level of particulates in a way the sensor results can test. DO NOT ALLOW 'traffic causes pollution' with no link to the level of particulates.

  2. 1 mark

    (reason) because vehicle engines burn fuels such as diesel and petrol, and incomplete combustion releases particulates (soot)

    ALLOW diesel engines release soot / burning fuels in engines produces particulates. ALLOW particulates also come from tyres and brakes wearing away. DO NOT ALLOW car exhausts release carbon dioxide (carbon dioxide is not a particulate).

  3. 1 mark

    (many places) the level of particulates is different in different parts of the city (for example higher beside busy roads than in parks), so sensors in many places give results that represent the whole city

    ALLOW so the sample is representative of the city / so the results can be compared between different places. IGNORE 'to make it a fair test' and 'to get more accurate results' on their own.

  4. 1 mark

    (every hour for a year) the level of particulates changes with time (time of day, rush hour, day of the week, season, weather), so readings over a whole year show the typical levels / give a reliable mean

    ALLOW one day could be unusual (for example a windy day or a day with little traffic). ALLOW many readings mean that an unusual (anomalous) reading has less effect on the mean.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.