Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
Avg
score:
–
Topics
done:
0/24

Practical skills: planning and making measurements

Practise 15 exam-style questions on Practical skills: planning and making measurements for OCR GCSE Combined Science (Chemistry Paper 10). Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 15 questions
  • 1–6 marks each
  • Instant marking
  • No sign-up needed
15 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

In bioleaching, bacteria release copper ions from low-grade copper ores. The solution that drains from the ore, called the leachate, is acidic and has a strong blue-green colour.

A scientist needs to measure the pH of the leachate to one decimal place.

Which method should the scientist use?

Choose your answer.

  • A Add a few drops of phenolphthalein.
  • B Add a few drops of universal indicator.
  • C Dip blue litmus paper into a sample.
  • D Use a calibrated pH meter.

Model answer

D. A calibrated pH meter reads the pH to one decimal place, and its reading does not depend on the colour of the solution.

Explanation

Indicators are judged by colour, so a strongly coloured solution makes them unreliable, and universal indicator only gives whole-number pH values. Litmus and phenolphthalein only show whether a solution is acidic or alkaline. A pH meter is calibrated first with buffer solutions of known pH.

Mark scheme
  1. 1 mark

    D / Use a calibrated pH meter.

    The only correct answer is D: a pH meter gives a numerical reading to one decimal place (or more) and its reading is not affected by the colour of the leachate. A is not correct because phenolphthalein is colourless in every acidic solution, so it cannot give a pH value; B is not correct because universal indicator gives the pH only to the nearest whole number, and the blue-green colour of the leachate would change the colour seen; C is not correct because blue litmus only shows that the solution is acidic (it turns red), not its pH. ALLOW the letter or the option. If more than one option is given, do not award the mark.

Question 2

2 marks

A student is going to make copper(II) sulfate crystals. She needs to add about 0.8 g of copper(II) oxide powder to warm dilute sulfuric acid, and she must know the mass of copper(II) oxide added accurately. She considers two methods.

Method 1: Put copper(II) oxide in a weighing boat and weigh it. Tip the powder into the acid. Weigh the empty boat again and subtract.

Method 2: Put the empty weighing boat on the balance and set the balance to zero. Add copper(II) oxide until the balance reads 0.80 g. Tip the powder into the acid and record the mass added as 0.80 g.

In Method 1, her readings are 3.47 g and then 2.69 g.

Explain why Method 1 gives a more accurate value for the mass of copper(II) oxide added.

Model answer

When the powder is tipped out, some of it stays stuck to the weighing boat. Method 1 weighs the boat again afterwards, so the difference (3.47 − 2.69 = 0.78 g) is the mass that actually went into the acid. Method 2 assumes that all 0.80 g went in, so the mass it records is higher than the true mass added.

Explanation

Weighing by difference is a standard technique for transferring a solid accurately: weigh the container with the solid, transfer it, then reweigh the container. It allows for any solid left behind. Setting the balance to zero only records the mass put into the boat, not the mass that reached the reaction.

Mark scheme
  1. 1 mark

    some of the powder stays in / sticks to the weighing boat when it is tipped out

    ALLOW 'not all the powder leaves the boat'.

  2. 1 mark

    Method 1 (weighing by difference) measures only the mass that actually left the boat (3.47 − 2.69 = 0.78 g), but Method 2 assumes all 0.80 g was added, so its recorded mass would be too high

    ALLOW the idea that reweighing the boat takes account of any powder left behind. ALLOW 0.78 g as the mass added in Method 1. IGNORE references to the resolution of the balance.

Question 3

3 marks

A student mixes bromine water with potassium iodide solution in a test tube. The mixture turns brown. Dilute bromine water and dilute iodine solution have similar colours, so she cannot tell from the brown colour whether iodine has been made.

She then adds 1 cm³ of hexane, puts a stopper in the tube, shakes it and lets it stand. Hexane does not mix with water and floats on top of it. Halogens dissolve much better in hexane than in water. In hexane, bromine is orange-red and iodine is purple.

Hexane is highly flammable.

Explain how adding hexane helps the student decide whether iodine has been made, and give one safety precaution she should take when using hexane.

Model answer

In water, bromine and iodine both give similar brown colours. When hexane is added and shaken, the halogen moves into the hexane layer on top, where bromine is orange-red and iodine is purple, so the two are easy to tell apart. If iodine has been made, the top (hexane) layer turns purple. Hexane is highly flammable, so all Bunsen burners must be turned off and there must be no naked flames nearby.

Explanation

Moving a halogen into a hydrocarbon solvent is a technique for making an observation clearer: the colours of bromine and iodine in hexane are very different, while in water they look alike. The hexane floats, so the colour to look for is in the top layer. A safety precaution should match the hazard given, here flammability, so 'wear goggles' on its own does not answer the question.

Mark scheme
  1. 1 mark

    the halogen (bromine or iodine) moves into / dissolves in the hexane (top) layer, where bromine and iodine have very different colours (orange-red and purple), so they are easy to tell apart

    ALLOW the idea that the colours are clearer / more distinct in hexane than in water. IGNORE 'hexane reacts with the halogen'.

  2. 1 mark

    if iodine has been made, the hexane (top) layer turns purple

    ALLOW violet / lilac for purple. DO NOT ALLOW 'the bottom layer turns purple' or 'the solution turns purple' with no reference to the top / hexane layer. DO NOT ALLOW orange-red.

  3. 1 mark

    no naked flames nearby / all Bunsen burners turned off / use it in a fume cupboard or a well-ventilated room / keep the stopper on the tube and use only a small volume

    The precaution must reduce the risk from the flammable liquid or its vapour. IGNORE general precautions such as 'wear goggles', 'wear gloves' or 'tie hair back' on their own.

Question 4

4 marks

A student wants to make at least 2.0 g of copper by adding iron powder to copper(II) sulfate solution.

Fe(s) + CuSO₄(aq) → FeSO₄(aq) + Cu(s)

The copper(II) sulfate solution has a concentration of 0.50 mol/dm³.

Relative atomic mass (Ar): Fe = 55.8   Cu = 63.5

Calculate the minimum volume of copper(II) sulfate solution, in cm³, that she must use.

Then calculate the mass of iron that would react with all of the copper(II) sulfate in this volume.

Model answer

Moles of copper = 2.0 ÷ 63.5 = 0.0315 mol
Moles of CuSO₄ needed = 0.0315 mol (1 : 1 ratio)
Volume = 0.0315 ÷ 0.50 = 0.0630 dm³ = 63 cm³
Moles of iron needed = 0.0315 mol (1 : 1 ratio)
Mass of iron = 0.0315 × 55.8 = 1.76 g
So she needs at least 63 cm³ of solution, and 1.76 g of iron would react with all of it (she should add more than this so that the iron is in excess).

Explanation

Planning the quantities for a preparation uses the balanced equation: every 1 mol of copper needs 1 mol of CuSO₄ and 1 mol of Fe. Volume (dm³) = moles ÷ concentration, then multiply by 1000 for cm³. Common errors are dividing 2.0 g by the Ar of iron instead of copper and forgetting to convert dm³ to cm³.

Mark scheme
  1. 1 mark

    moles of copper = 2.0 ÷ 63.5 = 0.0315 (mol); or a correct final answer of 63 cm³ and 1.76 g with no working

    An answer of 63 cm³ and 1.76 g with no working scores 4 marks. An answer of 63 cm³ alone with no working scores marking points 1, 2 and 3; an answer of 1.76 g alone with no working scores marking points 1 and 4. ALLOW 0.031 / 0.03150 mol. ALLOW 1.8 g for the mass of iron. ALLOW ECF throughout from an incorrect number of moles of copper shown in the working; for example, using 2.0 ÷ 55.8 = 0.0358 mol gives 72 cm³ and 2.0 g, which scores 3 marks (marking points 2, 3 and 4 by ECF).

  2. 1 mark

    volume = 0.0315 ÷ 0.50 = 0.063 (dm³); or a correct final answer of 63 cm³ and 1.76 g with no working

    ALLOW the 1 : 1 ratio of Cu to CuSO₄ used without comment. ALLOW 0.0630 dm³.

  3. 1 mark

    volume = 63 cm³; or a correct final answer of 63 cm³ and 1.76 g with no working

    ALLOW 63.0 cm³ / 62.99 cm³. DO NOT ALLOW 0.063 cm³ (not converted). ALLOW ECF from an incorrect volume in dm³ correctly multiplied by 1000.

  4. 1 mark

    mass of iron = 0.0315 × 55.8 = 1.76 (g)

    ALLOW 1.8 g / 1.757 g / 1.76 g. ALLOW ECF from an incorrect number of moles of copper.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.