Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
Avg
score:
–
Topics
done:
0/24

Explaining rates: collision theory and surface area

Practise 17 exam-style questions on Explaining rates: collision theory and surface area for OCR GCSE Combined Science (Chemistry Paper 10). Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 17 questions
  • 1–6 marks each
  • Instant marking
  • No sign-up needed
17 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

A student crushes a large marble chip into many small pieces. None of the marble is lost.

Which quantity stays the same?

Choose your answer.

  • A the number of marble particles exposed on the surface
  • B the surface area of the marble
  • C the surface area to volume ratio of the marble
  • D the total volume of the marble

Model answer

D - the total volume of the marble

Explanation

Crushing a solid does not change how much of it there is, so its total volume and mass stay the same. Every break creates new surfaces, so the total surface area, the number of exposed particles and the surface area to volume ratio all increase. This is why smaller pieces of the same mass react faster.

Mark scheme
  1. 1 mark

    D / the total volume of the marble

    The only correct answer is D: no marble is lost, so the pieces together have the same volume (and mass) as the chip. A is not correct because crushing exposes particles that were inside the chip, so more particles are on the surface. B is not correct because each break makes new faces, so the total surface area increases. C is not correct because the surface area increases while the volume stays the same, so the surface area to volume ratio increases. ALLOW the letter or the option. If more than one option is given, do not award the mark.

Question 2

2 marks

A student adds one large marble chip to a large excess of dilute hydrochloric acid. The concentration of the acid hardly changes during the reaction, but the rate of reaction still falls steadily as the reaction goes on.

Explain why the rate falls. Use ideas about surface area and collisions.

Model answer

As the chip reacts it gets smaller, so its surface area decreases and fewer particles of calcium carbonate are exposed to the acid. The acid particles collide with the surface of the marble less frequently, so there are fewer successful collisions per second and the rate falls, even though the concentration of the acid stays almost the same.

Explanation

The rate of a reaction between a solid and a solution depends on how often particles of the solution hit the surface of the solid. With the acid in large excess its concentration hardly changes, so the fall in rate must come from the shrinking surface area of the solid. A common error is to say the acid is being used up, which the question rules out.

Mark scheme
  1. 1 mark

    the marble chip gets smaller as it reacts, so its surface area decreases

    ALLOW fewer calcium carbonate particles are exposed on the surface of the chip. IGNORE the marble is used up, on its own. DO NOT ALLOW the acid is used up / the concentration of the acid falls (the acid is in large excess).

  2. 1 mark

    so acid particles / hydrogen ions collide with the marble less frequently / there are fewer collisions per second (so fewer successful collisions per second)

    IGNORE fewer collisions, on its own. DO NOT ALLOW the particles have less energy.

Question 3

2 marks

Carbon monoxide gas reacts with nitrogen dioxide gas.

CO(g) + NO₂(g) → CO₂(g) + NO(g)

A scientist mixes the two gases in a sealed container with a fixed volume, at a constant temperature. She then pumps some argon into the container. Argon does not react.

The total pressure in the container increases, but the rate of reaction does not change.

Explain why the rate of reaction does not change.

Model answer

Argon does not react, so adding it does not change the number of carbon monoxide and nitrogen dioxide molecules in the container, which has a fixed volume. The concentrations of the reactants are the same, so CO and NO₂ molecules collide with each other just as frequently as before. Collisions with argon atoms do not produce any products, so the rate does not change.

Explanation

Increasing the pressure of a gas reaction usually increases the rate because it puts more reactant particles into the same volume. Here the extra pressure comes from a gas that does not react, so the reactant particles are no more crowded. The rate depends on how often reactant particles collide, not on the total pressure.

Mark scheme
  1. 1 mark

    the number of carbon monoxide and nitrogen dioxide particles in the same volume does not change / the concentrations of the reactants do not change

    ALLOW argon is not a reactant, so the reactant particles are no more crowded. ALLOW the extra pressure is due only to the argon particles. The idea that the reactant particles are no more crowded is needed for this mark.

  2. 1 mark

    so the frequency of collisions between CO and NO₂ particles (between reactant particles) does not change

    ALLOW collisions with argon particles are not successful / do not form products. IGNORE the temperature is the same, on its own.

Question 4

4 marks

Increasing the pressure is often used in industry to increase the rate of reactions between gases. Increasing the pressure has almost no effect on the rate of reactions in solution.

Use the particle model to explain this difference.

Model answer

In a gas the particles are far apart, with a lot of space between them. Increasing the pressure squashes the gas into a smaller volume, so there are more particles in the same volume and they collide more frequently, which increases the rate. In a solution the particles are already close together and touching, so the liquid can hardly be compressed. Increasing the pressure does not put more particles into the same volume, so the frequency of collisions, and the rate, hardly change.

Explanation

This question links collision theory to the particle model of states of matter (C1.1). Pressure speeds up a gas reaction because it changes the concentration of the gas particles; it cannot do this for a liquid or solution, whose particles are already touching. Explain both halves: why it works for gases and why it does not for solutions.

Mark scheme
  1. 1 mark

    in a gas the particles are far apart / there is a lot of space between the particles

    ALLOW gases can be compressed (because of the space between the particles).

  2. 1 mark

    increasing the pressure (of a gas) pushes the particles closer together / puts more particles in the same volume / increases the concentration

    DO NOT ALLOW increasing the pressure gives the particles more energy / makes them move faster.

  3. 1 mark

    so the gas particles collide more frequently / there are more collisions per second (so the rate increases)

    IGNORE more collisions, on its own.

  4. 1 mark

    in a liquid / solution the particles are already close together / touching, so increasing the pressure (hardly) changes the number of particles in the same volume / so the frequency of collisions (and the rate) hardly changes

    ALLOW liquids / solutions cannot be compressed (much). The idea that the particles in a liquid are close together or touching is needed for this mark.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.