Level:
Correct: 0
Incorrect: 0
Marks: 0/0

Practical skills: planning and making measurements

Practise 15 exam-style questions on Practical skills: planning and making measurements for OCR GCSE Combined Science (Physics Paper 12). Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 15 questions
  • 1–6 marks each
  • Instant marking
  • No sign-up needed
15 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

A student's theory is that an alpha particle loses some energy each time it ionises an atom, and that alpha particles ionise so many air molecules that they lose all their energy in a few centimetres of air.

She has a sealed source that emits only alpha particles, a Geiger-Müller tube and counter, and a metre rule.

Which hypothesis is based on her theory?

Choose your answer.

  • A As the tube is moved away from the source, the count rate will fall steadily until it reaches background at about 1 m.
  • B Beyond a few centimetres from the source, the count rate will fall sharply to the background count rate.
  • C The count rate will be the same at every distance up to 1 m, because alpha particles travel in straight lines.
  • D The count rate will increase as the tube is moved further away, because the alpha particles spread out.

Model answer

B

If every alpha particle loses all its energy in a few centimetres of air, then when the tube is further away than this no alpha particles reach it, so the count rate drops sharply to the background count rate.

Explanation

A hypothesis is a testable prediction that follows from a theory. Here the theory says alpha particles have a short, definite range in air, so the hypothesis is that the count rate drops to background beyond that range. The student can test it by measuring the count rate at increasing distances with the metre rule and comparing it with the background count rate.

Mark scheme
  1. 1 mark

    B / beyond a few centimetres from the source, the count rate will fall sharply to the background count rate

    The only correct answer is B: if the alpha particles lose all their energy in a few centimetres of air, none of them reach the tube when it is further away than this, so only background radiation is counted. A is not correct because the theory predicts that the alpha particles are all stopped within a few centimetres, not that the count falls gradually over 1 m; C is not correct because the theory says the alpha particles are stopped by the air, so the count rate cannot stay the same; D is not correct because spreading out means fewer alpha particles reach the tube further away, not more. ALLOW the letter or the option. If more than one option is given, do not award the mark.

Question 2

2 marks

A teacher shines the beam from a green laser pointer into a tank of water to show a class how light refracts at the surface of the water.

Suggest two precautions the teacher should take to reduce the risk to the students' eyes.

Model answer

1. Never look into the beam or point it at anyone, and switch the laser on only when it is aimed at the tank.
2. Keep the beam low and horizontal, below the students' eye level, and put a matt black screen behind the tank so that the beam, and any reflections from the water surface or the glass, cannot reach anyone's eyes.

Explanation

A laser beam is narrow and concentrated, so even a low-power beam can damage the retina if it enters the eye directly or after reflecting from a shiny surface. Precautions therefore keep the beam, and its reflections, away from eye level. Ordinary sunglasses do not give reliable protection, so they are not credited.

Mark scheme
  1. 2 marks

    1 mark for each different precaution, max 2: never look into the beam or point the laser at anyone; switch the laser on only when it is aimed at the tank; keep the beam low and horizontal, below the students' eye level (for example with the students seated); stop the beam with a matt (black) screen behind the tank / block the beam where it comes out of the tank; remove or cover shiny objects (jewellery, watches, metal) that could reflect the beam towards someone / watch for reflections from the water surface and the glass; use a low-power (class 2) laser pointer; do not let students use the laser (only the teacher uses it)

    1 mark for each different precaution, max 2. 'Never look into the beam' and 'never point the laser at anyone' count as one precaution. IGNORE 'wear sunglasses / goggles / dark glasses'. IGNORE 'be careful'.

Question 3

3 marks

Two students stretch a slinky spring to a length of 4.0 m along a smooth floor. One student holds her end still. The other student makes a single pulse by moving his end quickly sideways and back.

The pulse travels along the slinky, reflects from the far end and travels back.

To reduce the effect of their reaction times, the students time the pulse over 6 lengths of the slinky instead of 1 length. Their time for 6 lengths is 5.2 s.

Calculate the speed of the pulse.

Suggest why the students do not time the pulse over many more lengths, such as 20 lengths.

Model answer

distance travelled = 6 × 4.0 = 24 m
speed = distance ÷ time = 24 ÷ 5.2 = 4.6 m/s
Each time the pulse travels along the slinky, some of its energy is dissipated, so the pulse gets smaller. After a few more lengths it would be too small to see clearly, so the students could not tell when it had travelled 20 lengths.

Explanation

Use speed = distance ÷ time with the total distance the pulse travels (6 lengths = 24 m), not one length; dividing 4.0 m by the time for six lengths is a common mistake. Timing several lengths makes the reaction-time error a smaller fraction of the measured time, but the number of lengths is limited because the pulse loses energy and dies away.

Mark scheme
  1. 1 mark

    (speed =) distance ÷ time = (6 × 4.0) ÷ 5.2 / 24 ÷ 5.2 / 4.0 ÷ (5.2 ÷ 6); or a correct final answer of 4.6 m/s with no working

    An answer of 4.6 m/s with no working scores marking points 1 and 2. ALLOW 1 mark for 0.77 m/s (4.0 ÷ 5.2, using one length only). ALLOW 0.87 s as the time for one length.

  2. 1 mark

    4.6 (m/s)

    ALLOW 4.62 m/s / 4.615 m/s. IGNORE units.

  3. 1 mark

    the pulse loses energy / gets smaller (its amplitude decreases) each time it travels along the slinky, so after a few more lengths it dies away / is too small to see, and they could not tell when it had travelled that many lengths

    ALLOW 'the pulse would die away before it had travelled 20 lengths'. ALLOW 'energy is dissipated (for example by friction with the floor), so the pulse fades'. ALLOW 'they could lose count of the number of lengths'. IGNORE 'it would take too long'.

Question 4

4 marks

A student measures the speed of sound in air using a long, straight plastic pipe that is closed at one end. She fixes a microphone just inside the open end of the pipe and connects it to a data logger. She makes a single short click next to the microphone. The click travels along the pipe, reflects from the closed end and returns to the microphone as an echo.

The data logger records the signal from the microphone against time, with a resolution of 0.1 ms. She measures the length of the pipe with a tape measure.

Explain why:
• the microphone is placed at the open end of the pipe, where the click is made
• she makes a short click rather than a long note
• she sends the sound along a closed pipe rather than towards a wall in an open space.

State how she should use her measurements to calculate the speed of sound.

Model answer

The microphone is at the open end so that it records both the click and its echo; the time between the two signals is then the time for the sound to travel to the closed end of the pipe and back.
The click must be short so that it has finished before the echo returns. The echo arrives after only a few hundredths of a second, so a long note would overlap with it and the start of the echo could not be seen on the trace.
In the pipe the sound cannot spread out, so the echo is still loud enough to detect, and the sound travels along a fixed path whose length can be measured, with no echoes from other surfaces.
Speed of sound = (2 × length of the pipe) ÷ time between the start of the click and the start of the echo.

Explanation

In an echo method the sound travels to the reflector and back, so the distance is twice the length of the pipe; using the length alone gives half the speed. Each choice in the method makes the time measurement reliable: the microphone records both signals, the short click keeps them separate and the pipe keeps the echo strong. The data logger can measure a time of a few hundredths of a second, which is far too short to time with a stopwatch.

Mark scheme
  1. 1 mark

    (microphone at the open end) it detects both the click and the echo, so the time between the two signals is the time for the sound to travel to the closed end of the pipe and back

    1 mark for each point. ALLOW 'so the sound travels exactly twice the length of the pipe between the two signals'. IGNORE 'so that it can hear the sound' with no reference to the echo.

  2. 1 mark

    (short click) the click has ended before the echo returns, so the two signals are separate on the trace and the start of each can be timed / a long note would still be sounding when the echo arrived, so the two signals would overlap

    ALLOW 'the echo returns after only a few hundredths of a second, so a longer sound would overlap with it'. IGNORE 'a click is louder'.

  3. 1 mark

    (closed pipe) the sound cannot spread out, so the echo is still loud enough to detect / the sound travels along a fixed path whose length can be measured, with no echoes from other surfaces

    ALLOW 'the distance travelled by the sound is known exactly (twice the length of the pipe)'. IGNORE 'it is more accurate' with no reason.

  4. 1 mark

    speed of sound = (2 × length of the pipe) ÷ time between the start of the click and the start of the echo (read from the trace)

    ALLOW distance travelled = 2 × length, then speed = distance ÷ time. DO NOT ALLOW speed = length ÷ time.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.