Level:
Correct: 0
Incorrect: 0
Marks: 0/0

Mains electricity and safety

Practise 17 exam-style questions on Mains electricity and safety for OCR GCSE Combined Science (Physics Paper 12). Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 17 questions
  • 1–6 marks each
  • Instant marking
  • No sign-up needed
17 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

In a mains circuit, an appliance is switched on and working normally.

Which wire is at a potential difference of about 0 V relative to earth and also carries the current through the appliance?

Choose your answer.

  • A both the live wire and the neutral wire
  • B the earth wire
  • C the live wire
  • D the neutral wire

Model answer

D (the neutral wire)

Explanation

The live wire carries the alternating p.d. of about 230 V relative to earth; the neutral wire completes the circuit and stays at about 0 V; the earth wire is a safety wire at 0 V that carries a current only when there is a fault. Both the live and the neutral wire carry the appliance's current, but only the neutral is close to 0 V. A common misconception is that the neutral wire carries no current.

Mark scheme
  1. 1 mark

    D / the neutral wire

    The only correct answer is D: the neutral wire completes the circuit, carrying the current back from the appliance to the supply, and it is at a potential difference of about 0 V relative to earth. A is not correct because the live wire is at about 230 V relative to earth; B is not correct because the earth wire is at 0 V but carries no current when the appliance works normally (only if there is a fault); C is not correct because the live wire carries the current but is at about 230 V relative to earth. ALLOW the letter or the option. If more than one option is given, do not award the mark.

Question 2

2 marks

A student places a plotting compass on a bench, directly under a long straight wire. She connects the wire to a low-voltage d.c. supply, so that the current in the wire is 5 A. The compass needle turns through a large angle and stays in its new position.

She then connects the wire to a low-voltage a.c. supply with a frequency of 50 Hz. The current is again 5 A, but the compass needle stays where it points when there is no current. It only trembles slightly.

Explain the difference between her observations.

Model answer

The direct current is always in the same direction, so the magnetic field around the wire is always in the same direction. This field turns the compass needle and keeps it in its new position.

The alternating current reverses direction 100 times each second, so the magnetic field around the wire keeps reversing too. The force on the needle changes direction far too quickly for the needle to turn, so it stays where it points with no current and only trembles.

Explanation

The difference between direct and alternating current is about direction: a direct current is always in one direction, while an alternating current at 50 Hz reverses 100 times each second. A current in a wire has a magnetic field whose direction depends on the direction of the current, so a.c. gives a field that keeps reversing, and the compass needle cannot follow it. Saying only that a.c. 'changes' does not explain why the needle does not turn.

Mark scheme
  1. 1 mark

    (d.c.) the direct current is always in the same direction, so its magnetic field (around the wire) is always in the same direction, so it turns the needle and holds it in its new position

    Max 1 if only one supply is explained. ALLOW the d.c. supply's p.d. always acts in one direction. IGNORE the direct current is constant / stays the same, on its own.

  2. 1 mark

    (a.c.) the alternating current reverses direction (100 times each second), so its magnetic field keeps reversing, and the force on the needle reverses too quickly for the needle to turn (so it stays where it was and only trembles)

    ALLOW the alternating current changes direction many times each second. IGNORE the number of reversals each second (for example 50). ALLOW the needle cannot respond (move) fast enough to follow the changes of direction. IGNORE the a.c. changes / varies / alternates, on its own. DO NOT ALLOW a.c. produces no magnetic field / the a.c. current is too small.

Question 3

3 marks

Some older electric clocks keep time by counting the cycles of the alternating potential difference of the mains supply. Each clock is designed for the normal frequency of the UK mains supply.

One evening, the frequency of the UK mains supply stays at 49.8 Hz for exactly one hour.

Calculate how many seconds slow one of these clocks is at the end of the hour.

Model answer

The UK mains frequency is normally 50 Hz, so the clock moves on 1 second for every 50 cycles.
Cycles in one hour at 49.8 Hz = 49.8 × 3600 = 179 280
Time shown by the clock = 179 280 ÷ 50 = 3585.6 s
The clock is 3600 − 3585.6 = 14.4 s slow.

Explanation

A frequency of 50 Hz means 50 complete cycles every second, and this value has to be recalled. At 49.8 Hz the supply completes 0.2 fewer cycles each second, so in one hour 720 cycles are missed, which the clock counts as 720 ÷ 50 = 14.4 s. A common error is to give 720 as the answer, which is a number of cycles, not seconds.

Mark scheme
  1. 1 mark

    recall: the normal frequency is 50 Hz, so the clock moves on one second for every 50 cycles; or a correct final answer of 14.4 s or 14 s with no working

    An answer of 14.4 s or 14 s with no working scores 3 marks. ALLOW 2 marks for 720 (the number of cycles missed, not converted to seconds). ALLOW 2 marks for 14.5 s (3600 × 50 ÷ 49.8 − 3600, the extra time the clock takes to show one hour). If a normal frequency other than 50 Hz is used, do not award marking point 1, but ALLOW ECF for marking points 2 and 3.

  2. 1 mark

    cycles in one hour = 49.8 × 3600 = 179 280, so the clock shows 179 280 ÷ 50 = 3585.6 s; or a correct final answer of 14.4 s or 14 s with no working

    ALLOW cycles missed = (50 − 49.8) × 3600 = 720, and 720 ÷ 50. ALLOW time shown = (49.8 ÷ 50) × 3600. ALLOW 0.2 ÷ 50 = 0.004 (s lost each second) × 3600.

  3. 1 mark

    evaluation: 3600 − 3585.6 = 14.4 (s)

    ALLOW 14 s. IGNORE units unless the question asks for them.

Question 4

4 marks

A loose live wire inside a metal-cased toaster touches the case. The case is connected to the earth wire, so there is now a path from the live wire to earth. The resistance of this path is 0.40 Ω.

The current in the path is 575 A until the fuse in the toaster's plug melts after 0.010 s.

Calculate the energy transferred in the path from the live wire to earth during this time.

Suggest one danger caused by this energy transfer.

Model answer

Power in the path = (current)² × resistance = 575² × 0.40 = 132 250 W
Energy transferred = power × time = 132 250 × 0.010 = 1322.5 J ≈ 1300 J

This energy is transferred to the thermal store of the wires in a hundredth of a second, so the wires get very hot very quickly. The insulation could melt, and a fire could start, especially if the fuse did not melt.

Explanation

Recall P = I² × R to find the power in the fault path, then E = P × t; or do it in one step with E = I² × R × t. A common error is to forget to square the current, which gives only 2.3 J. The huge current in a live-to-earth connection is why such a connection is dangerous even when nobody touches it: the heating can melt insulation or start a fire, especially if the fuse does not melt quickly.

Mark scheme
  1. 1 mark

    recall and substitution: power = (current)² × resistance = 575² × 0.40; or a correct final answer of 1300 J, 1320 J or 1322.5 J with no working

    An answer of 1300 J, 1320 J or 1322.5 J with no working scores marking points 1, 2 and 3. ALLOW (P =) I² × R. ALLOW the route p.d. = 575 × 0.40 = 230 V, then power = 230 × 575. ALLOW 2 marks for 1 322 500 J (time used as 10 instead of 0.010 s). An answer of 2.3 J (575 × 0.40 × 0.010, current not squared) scores 0 for the calculation.

  2. 1 mark

    power = 132 250 (W), and recall: energy transferred = power × time = 132 250 × 0.010; or a correct final answer of 1300 J, 1320 J or 1322.5 J with no working

    ALLOW 1.3 × 10⁵ W / 132 kW. ALLOW E = I² × R × t in one step. ALLOW ECF from a wrong power.

  3. 1 mark

    evaluation: 1322.5 (J) / 1320 (J) / 1300 (J)

    ALLOW 1.3 kJ / 1.32 kJ. ALLOW 1323 J. IGNORE units unless the question asks for them.

  4. 1 mark

    danger: the wires in the path (the earth wire / the cable / the loose wire) get very hot very quickly, so the insulation could melt or burn / a fire could start / sparks could be produced

    ALLOW the plug or the toaster could catch fire. ALLOW burns to anyone touching the cable. DO NOT ALLOW electric shock / electrocution (the question asks about the energy transfer in the path). IGNORE the fuse melts (that is the safety feature).

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.