Level:
Correct: 0
Incorrect: 0
Marks: 0/0
Exam Practice
Course:
Topics:
Avg
score:
–
Topics
done:
0/27

Measuring speed, typical speeds and accelerations

Practise 14 exam-style questions on Measuring speed, typical speeds and accelerations for Edexcel GCSE Combined Science (Physics Paper 1). Write your answer as you would in the exam and get it marked in seconds against the mark scheme, point by point, with the Study Helper on hand if you get stuck.

  • 14 questions
  • 1–6 marks each
  • Instant marking
  • No sign-up needed
14 questions, marked as you go

Sample questions with model answers

Here are 4 of the questions in this topic, each with a model answer, an explanation of why it earns the marks and the mark scheme an examiner would use.

Question 1

1 mark

Which of these is the best estimate of the acceleration of a passenger train as it pulls away from a station?

Choose your answer.

  • A 0.5 m/s²
  • B 5 m/s²
  • C 50 m/s²
  • D 500 m/s²

Model answer

A - 0.5 m/s².

Explanation

A useful check is to compare with g = 10 m/s², the acceleration of free fall. A train taking about a minute to reach 30 m/s has an acceleration of about 30 ÷ 60 = 0.5 m/s². Accelerations comparable with g feel very strong to passengers, which is why trains, buses and lifts accelerate gently.

Mark scheme
  1. 1 mark

    A / 0.5 m/s² (1)

    The only correct answer is A: passenger trains accelerate gently, at about 1 m/s² or less (roughly 0.5 m/s² for many trains, up to about 1.3 m/s² for metro trains), so that standing passengers can keep their balance. B is not correct because 5 m/s² is half the acceleration of free fall - more like a powerful sports car or a sprinter leaving the blocks; C is not correct because 50 m/s² is five times the acceleration of free fall, which only happens briefly, e.g. in a collision; D is not correct because 500 m/s² is far too large for any vehicle carrying people. Accept the letter or the option. If more than one option is given, do not award the mark.

Question 2

2 marks

A launched rollercoaster accelerates uniformly from rest to 28 m/s in 2.5 s.

The ride's website says: 'On the launch, riders accelerate faster than an object falling freely.'

Use a calculation to decide whether the website is correct.

Model answer

a = (v − u) ÷ t = (28 − 0) ÷ 2.5 = 11.2 m/s²
The acceleration of an object falling freely is g = 10 m/s². 11.2 m/s² is greater than 10 m/s², so the website is correct.

Explanation

Calculate the launch acceleration with a = (v − u) ÷ t, then compare it with the recalled value g = 10 m/s². Accelerations a little above g are typical of the most powerful rides and feel very strong; everyday vehicles accelerate at only a fraction of g.

Mark scheme
  1. 1 mark

    acceleration = 28 ÷ 2.5 = 11.2 (m/s²) (1)

    Accept 11 (m/s²). Accept (28 − 0) ÷ 2.5. Award this mark for 11.2 (m/s²) seen without working. Do not accept 2.5 ÷ 28 or 28 × 2.5.

  2. 1 mark

    (the website is correct because) 11.2 m/s² is greater than (the acceleration in free fall) g = 10 m/s² (1)

    The comparison must use a recalled value of g of about 10 m/s² (allow 9.8 m/s²). Allow ecf from a wrong acceleration only if the comparison with g is correct for their value. Ignore 'about the same as g' if 'greater' is also stated. 'Yes' alone with no comparison scores 0 for this mark.

Question 3

3 marks

A car on a slip road joining a motorway is travelling at 15 m/s. The car then accelerates uniformly for 6.0 s until it reaches a typical motorway speed.

Estimate the acceleration of the car.

Model answer

A typical motorway speed is about 30 m/s (70 mph is about 31 m/s).
a = (v − u) ÷ t = (30 − 15) ÷ 6.0
a = 2.5 m/s²

Explanation

Estimating means choosing a sensible value for anything not given - here a typical motorway speed of about 30 m/s - and then using a = (v − u) ÷ t. The change in velocity is (30 − 15) m/s, not 30 m/s, because the car was already moving. An answer of about 2-3 m/s² is a typical everyday acceleration for a car.

Mark scheme
  1. 1 mark

    a typical motorway speed in the range 25 to 35 m/s used (1)

    Accept 70 mph or 110 km/h converted to about 31 m/s. A speed not in m/s must be converted before it is used.

  2. 1 mark

    substitution: (a =) (their motorway speed − 15) ÷ 6.0, e.g. (30 − 15) ÷ 6.0 (1)

    Allow ecf from their speed. Do not accept their motorway speed ÷ 6.0 (initial velocity ignored) for this mark or the next.

  3. 1 mark

    evaluation: correct value for their speed, e.g. 2.5 (m/s²) (1)

    With speeds in the range 25 to 35 m/s the answer is 1.7 to 3.3 m/s². Allow ecf from their speed. Award full marks for an answer in the range 1.7 to 3.3 m/s² without working (it can only come from a typical motorway speed).

Question 4

5 marks

A student uses a light gate to measure the acceleration of a falling card.

The card has two dark sections, each 2.0 cm long, with a clear gap between them. The student drops the card vertically through the light gate, so that each dark section blocks the light beam in turn.

The data logger records:
- the first section blocks the beam for 0.0100 s
- the second section blocks the beam for 0.0080 s
- the time between the middle of the first section and the middle of the second section passing the gate is 0.053 s.

Calculate the acceleration of the card. Suggest why it is less than the acceleration due to gravity, g.

Model answer

Speed of first section = 0.020 m ÷ 0.0100 s = 2.0 m/s
Speed of second section = 0.020 m ÷ 0.0080 s = 2.5 m/s
a = (v − u) ÷ t = (2.5 − 2.0) ÷ 0.053
a = 9.4 m/s²
This is less than g (10 m/s²) because air resistance acts upwards on the card as it falls, so the resultant force on it is less than its weight.

Explanation

Each dark section gives one speed (section length ÷ blocking time). The acceleration is the change between the two speeds divided by the time between them (0.053 s), not by either blocking time. A flat card has a large area, so air resistance is noticeable and the measured acceleration is a little less than the free-fall value of 10 m/s².

Mark scheme
  1. 1 mark

    speed of first section = 0.020 ÷ 0.0100 = 2.0 (m/s) (1)

    Allow 2.0 ÷ 0.0100 = 200 (cm/s) if used consistently with the second speed. Award the first four marks for an acceleration of 9.4 m/s² without working.

  2. 1 mark

    speed of second section = 0.020 ÷ 0.0080 = 2.5 (m/s) (1)

  3. 1 mark

    substitution: (a =) (2.5 − 2.0) ÷ 0.053 (1)

    Allow ecf from their speeds. Do not accept dividing by 0.0100, 0.0080 or 0.018 (the blocking times are not the time between the two speeds): a wrong method scores 0 for this mark and the next.

  4. 1 mark

    evaluation: 9.4 (m/s²) (1)

    Allow values that round to 9.4, e.g. 9.43. Accept 940 cm/s² (from speeds in cm/s) with the unit. 940 with m/s² or with no unit is a power of ten error and scores 3 of the first four marks.

  5. 1 mark

    air resistance / drag acts (upwards) on the card (so the resultant force is less than its weight) (1)

    Accept 'the card is slowed by the air' / 'friction with the air'. Ignore 'human error', 'the light gate is inaccurate' and 'the card was not dropped from rest'. Do not accept 'gravity is weaker in the lab'.

Ready to try the rest? Every answer you write is marked against the mark scheme, so you can see exactly where the marks are.

Study Helper Hints first, answers after you try

Stuck on this one? Ask for a hint and I’ll point you in the right direction, without giving the answer away. Once you’ve checked your answer, I’ll show you how the marks are awarded.